JDP36BW3WH General Electric Range - Instructions

Flipped off the circuit breaker first. Unscrewed the two screws holding the element in place. Pulled out about 4-5 inches. Tried several times to pull apart the connections, finally got 'em - don't give up (I must have weak fingers). Then plugged in the new element, shoved the wires back in, screwed it back in place, flipped circuit breaker back on, turned the oven on.... made brownies (o:

Open door lift door off hinges lay door face down on flat surface remove 6 phillip head screws 3 on each side lift housing out of door case remove end knob phillip head screws installed one knob insert bar attch second knob and tighten screws lay housing back into casing attach screws doing one at a time on each side slide door back on to hinges and test operate, you are done!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires,held wires one at a time so tehy wouln't slip back into rear holes in oven, slid off connector tabs and pushed on to replacement unit...)

Basically very easy. Be sure to follow suggested safe practices - DO shut off the circuit breaker to the unit BEFORE starting (I didn't to start with, shorted out the heater leads - dumb on my part). Just removed the burned out element by removing the 2 screws using a nutdriver, pulled the element out, and slipped off the crimp fittings. Reverse steps to install replacement. The crimp fittings were stubborn coming off the old one, so it took longer than expected. Otherwise, easy peasy.

I turned off electric to the stove. In the oven, I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. After unpacking the new element, I placed it in the bottom of the oven, reconnected the two wires, and gently fed the wires back into the back of the oven. I then secured the new unit to the oven wall with the two screws.

1. Turned off power at the breaker box. Removed oven door from oven, and removed bake racks. Determined replacement element from PartSelect was correct. Inspected new element. Using meter, determined new element was OK via continuity test. Gathered all appropriate tools to do the job.
2. Using 1/4" nut driver, removed two retaining screws at back of oven that secure element
3. Pulled bad element out a few inches from oven back to reveal wires and spade connectors
4. Using screwdriver, pushed off electrical connectors from bad element and removed element
5. Inspected wires and connectors and determined them to be OK
6. Installed new element in reverse of above. Inspected oven controls and determined them to be OK. Turned on the breaker. Tested oven.
7. Baked a delicious chocolate cake

Followed the instructions

Step #1: Remove 2 screws at the inside top of the oven door that holds the inner/outer oven door together. Step #2: Remove the screws from the inner door that hold the plastic handle end caps to the door. Tip: Use a file to dress up the tips of the metal handle bar so that it fits easily into the new plastic handle end caps. Step #3: Install the first new plastic handle end cap. Step #4: Slide the metal handle bar into the plastic handle end cap that was just installed on the outer oven door. Step #5: Place the other plastic handle end cap on the metal handle bar. Step #6: Install the second plastic handle end cap on the outer oven door. Step #7: Reassemble the oven door by installing the screws that were removed in step #1.

Before ordering, I took the element out to make sure I could do it. A flashlight was helpful.

I flipped off the circuit breakers to the stove, removed the racks and lifted off the oven door. Not having a nutdriver or socket set, I used a 6' crescent wrench to remove the two screws which hold the element to the back of the oven. I carefully pulled the element out until the spade connectors to the wires were exposed. I wiggled the connectors apart. I had pliers handy, but didn't need them.

I connected the new element to the wires and gently pushed the two connected prongs through their holes, trying not to disturb the insulation. I put a little WD-40 on the screws so they would go in easier. After tightening the screws with the crescent wrench, I replaced the racks and door. I flipped the circuit breaker back on and reset the clock. It works as good or better than new.

Unscrewed three screws from each oven door. Unbolted the end pieces and replaced with new ones. Reinstalled oven door screws. Nothing to it.

My dealer was unable to find the part even with a model number. Your accurate drawings allowed me to select correct part. It was a perfect replacement in every way and cheaper (by $10) than the dealer. Also quicker.

First I removed the two screws that hold the element in place, I then pulled the element out about three inches, and it shorted out on the main panel of the back of the range. I then went to the breaker box and flipped the switch so I could tell my wife "Yes, I had turned the power off."

Disconnecting the two wires and reconnecting them was a simple operation after I cleaned my pants from the electrical short.

Re attaching the two-screw panes to hold the element in place finished the project.

By myself

.First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and reversed the procedure with the new element very simple.

Rating: 5 Stars!! We cut the power, removed two screws disconnected the two wires (just pulled them out of the covers) from the old element and pushed in the new ones. It didn't take longer than 10 minutes!

This is the first time it's been as easy as promised! Great customer service in addition to easy and reasonable prices!
Thank you,