JBP21BY4 General Electric Range - Instructions

Surface element easily unplugged and removed, drip pans lifted out, New drip pans inserted, New 8" surface element and present 6" surface elements Inserted and plugged in.

I went online to find the part. I also found a how-todo it self installation instructions. So, I thought I would try it. I pulled the stove out and unplugged it. It took me 2 days to try and remove the screws. They wouldn't budge. On the second day, I was about to give up. I tried to loosen the screws again. It finally moved!! So, I kept at it. Took me about 10 mins on the first screw. Then another 10 or 15 minutes on the second one. Once I took the screws off, I didn't know how to remove the wires. I kept picking at them for about 5 minutes, and it was easy then. Removed the old bake element. Then connected the new element wires, put the screws back in (not tight). Plugged it up and tested it. It worked!!!!!! I've never did anything like this before. If the screws wouldn't have been so hard to remove;it would have went a lot better.

Removed existing surface element and replaced with new element.

P.S.

Part Select service was excellent.

took 2 screws out removed old element, put new element in and put the 2 screws back in. All worked great and I baked bread that same day. The service was fantastic, and $40.oo cheaper than the appliance store I checked with.

OK, I put the drip pan under the burner. Without a single problem.

ordered over the phone a new temp sensor. Un plug the oven, take off the back, open oven and unscrew the temp sensor, pull the sensor until the elec connector clip comes through so you can unclip the old sensor, clip on the new then pull the line back and re attach the sensor to the ovn. Plug in the oven.
Pretty simple, just hard to work inside the oven. I unclipped the sensor line outside the oven to make sure it would come apart first before I was working inside the oven.

baking element went bad. removed the 2 screws holding it in place. unscrewed the 2 connected wires. took the new element which is a plug in type and drilled holes to fit the screws. had to do this as the exact part needed is no longer made. works fine.

This is far to simple to even be a worthy story ,other than that the cause is a bit interesting. My wife had placed a plastic cutting board and some meat into the oven to get it away from my counter-cruising dog.
Later, without remembering the cutting board she turned the oven on to "broil." Hmmmm...

REPAIR:
Open oven door
Put in new rack
Close door

replaced lights in refrigirator and freezer

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Took Switch panel off range. Disconnected Infinite switch. Reinstalled infinite switch.. Replaced panel. Repair was very simple and self explainatory.
Knott County Housing Authority Maintenance Personnel

Because of the superb pics and descriptions on the Part Select site, I was able (with NO range model number) to order the correct range element for beloved son's stove. He plugged it in in 3 seconds, works great !

I removed the screws holding the element in place and pulled it out, then pulled the wires from the element out. Very easy. When I got the new part, it seemed like it would be simple. I plugged the new wires back in and started to push it in place to screw it in. Unfortunately, there was a big spark and everything died. I was afraid I had crossed the wires, and I'm still not sure how one is supposed to tell which wire plugs in to which holder in the oven. Luckily, I discovered that I had simply blown a fuse. Problem solved, everything works.

Removed the two screws which mount the element to the back of the stove.
The old element had screws connecting the wires to the heat element. The new element needed female electro-terms, so I crimped the appropriate electro terms on. If you need to do this make sure you use the correct electro-terms based on the wire size from the stove.
Installed new element in 2 minutes.
Parts Select had the part here within two days with standard ground shipping. Very impressed with service.
A clearer description of how the part connected to the wires from the stove would have been helpful.

I first removed the unit by pulling gently from connection. Replaced the new one in that same manner - simply inserting into connection.

Very easy, I'll probably try it again soon.