JSP28GV1BB General Electric Range - Instructions

As has been said shut down unit,Breaker fuse.If you do not have install info.Get a copy on line. If you have another set of hands it would not hurt.! this has been stated before. Remove door, Remove 4 screws , to slide unit out,I used a saw horse with some cribing secured to the horse to get height, Pull the oven out so that the two front supports are on the saw horse,and the back two are up to the edge runner.I used about a 1 ft stool for working height. Remove the top elec. cover sheet metal 2 screws. You will see were the wireing runs down the back. Get a small mirror,and flash light. Look down the wire opening in the back, you see the sensor connection ,I made a hook out of a coat hanger to grab it with. Pull it up before you disconnect it ,tie a piece of string to the sensor side of the connector , use 2 Ft. then disconnect remove two screws from inside the oven. And remove,sensor tie string on to new sensor connector pull through and connect.on top.Then replace everything cck every thing Twice!Doing this i didn"t have to pull the unit all the way out! LATER GOOD LUCK!

I removed the unit from the wall,removed the back panel to access the wires to the sensor,cut the plug off of the new sensor and strip the wires back,used the wire nuts to attach the new sensor,put all back together and slid back into the wall and works excellent.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) discovering a burnt spot in the element sent me searching for a new one. I couldn't find any locally, so I continued my search to the internet. This is when I came in contact with PartsSelect.com .
They made identifing the part and ordering so easy it was unbelievable. Super fast deliverey astounded me as well. The installation of the new element was reverse of the old. All of the dimensions and info for the part were right there on this site. Thanks

Turned the range/oven off at the breaker box. Pulled all the racks out. Unscrewed two screws holding lower heating element in. Pulled the heating element out to expose connections. Unhooked connections, plugged in new element. Replaced the screws. Turned breaker back one. Pretty simple!

It was very easy I removed two screws unpluged the sensor and wire spliced it together and also replaced the modual on the top of the stove and it was that easy.

DO NOT ATTEMPT THIS REPAIR UNTIL THE RANGE IS UNPLUGGED AND THE CIRCUIT BREAKER IS OFF!!!!!!

Very easy repair, but, either there is a minor amount of current flowing through the element at all times, or the off switch wasn't working when I started. didn't turn the breaker off, after I removed the nuts, as I was pulling the element to reveal the terminals, the terminals arc'd on the oven wall. BIG SPARKS!

After I turned the breaker off and started again. No problems.

No problem installing oven sensor, but I diagnose the problem wrong, I need to change(ERC-11)control p/n wb27k5140

I was able to remove the heating element but in the process one of the wires fell behind the back wall of the oven so I needed a little help getting it out. It was my first time working with electricity. If this didn't happen the repair would have been quit easy. The instructions were great.

This was so easy I should be a repairman! Turned off power at the breaker, used socket to unscrew two hex head screws, pulled out element slowly from the back of oven wall - enough to expose the wires about 3". Used pliers to remove clips from terminals, put new element in, pushed on new terminal clips, fed wires and terminals back through the two holes, replaced the hex head screws, turned breaker on and wallah! My wife was happy! That's a good thing.

Removed oven door from oven. Removed the inner oven door portion from the outer part to gain access to inner screws attaching end caps to front of stove door. Removed those screws and the old end caps & broken off pieces. Pressed oven door handle bar into new end caps. Reattached oven door handle assembly to front of oven door. Reinstalled inner oven door which included long screws that also went into the new end caps. Reinstalled oven door on oven. Job was easy. Price was certainly right for the end caps at $10.01/each.

The repair was easy, I took out the 4 screws and removed the outer shell, placed the glass in the bottom slot. lined up and started the handle screws, tighten them by hand gently. Then laid the outer over the inner door and re-inserted the 4 screws. Made sure it was all tight and slipped the door back over the hinge. Took about 10 min.
Wish I was more careful tightening the handle the first time, would have saved myself $55. Don't over tighten the handle!
Kudos to PartSelect, the part was a snap to find and order, easiest online website ever! It was here the next day even though I shipped it ground.
Thanks for making my big blunder easy to fix.

i was really pleased getting the order from partselect. i had torn my oven appart and knew i needed just this one part i came home and ordered it from parts select and actually got the part the next day.... very nice.... so pleased

remove two screws slide out. slide new one in. put two screws back. done.

First I unscrewed the end of the oven door and realized I could replaced the parts easily that hold the handle on the door. Then I held the sharp, broken plastic ends with a towel and used my drill with a thingy that fits on a small hex nut and unscrewed the broken handle parts and removed them. All I had to do after that is screw on the new handle holders with the handle bar fit snuggly between them, presto, new handle bar installed. Great service from partselect. com. Would use them again.!

I read the previous repair stories and figured it couldn't be that tough. Mine actually had a slight deviation and I'm sure based on model...
To remove the oven door handle, I had to remove 3 screws (phillips) on the top of the hinged door. This allowed the face plate to easily pull away from the inside of the door. The existing handles were held in place by a single hex head screw each.
Voila, in 2 minutes the entire handle was off.
This is where things had a slight deviation.
The door end caps I bought had 2 alignment prongs that extended beyond the actual surface. My door did not have holes for them to go into. No big deal, I took some wire snippers and clipped the little plastic prongs off so it was flush like my old ones. That took about 3 minutes because I had to go back into the garage to get the tool :-)
My metal door handle bar did not want to go all the way in very easily into the end caps. I went back into the garage and got some WD40 and sprayed into all pieces and wiggled things back and forth for a few minutes, placing it against the oven a couple of times to ensure I had the bar was seated enough where the holes lined up with the oven.
I would recommend putting the end caps on the bar PRIOR to attaching one side to the oven. I originally did not do this and when it was difficult to get the bar on, I had to take it off so I could perform the procedure I just mentioned.
Honestly, the entire "job" took 10 minutes.