JSP47CF2CC General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Anthony from Apopka, FL
- Parts Used:
- WB30X44826
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Burner no longer heats
Remove two screws with nut driver that holds range top down. Turn off breaker or unplug before lifting top. Brace top with 2x4. Take picture with cell phone just in case. Orient replacement part with old burner. Remove one wire at a time and install on new burner in corresponding correcting terminal. be sure they are snug. Drop top install nuts . Test! Done! I am not an electrician!!!!!!!! Please do not publish !!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Glencoe, NM
- Parts Used:
- WB23T10015
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Remove back panel or access sensor, replace sensor and panel
Removed back panel, change out sensor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Albert from South Boston, VA
- Parts Used:
- WB30T10099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
only the inner/smaller part of the dual burner is working
I ordered a new burner assuming As is turns out: nothing wrong with the burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Tierra Verde, FL
- Parts Used:
- WB30T10099
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
small (inner) burner was not 'burning'
turn off the power at the breaker first
remove the 2 screws under the 'lip' of the stove top (open the oven door to get to them)
prop up the stove top on the cardboard box the part came in
pull off the wires one by one and attach to the new burner OR record where each wire goes first
remove the old burner (2 screws) and attach the new burner
screw down the stove top
try the burner - when it does not work flip the power breaker back on and then try again
bask in the joy, admiration and wonder directed your way by various family members
remove the 2 screws under the 'lip' of the stove top (open the oven door to get to them)
prop up the stove top on the cardboard box the part came in
pull off the wires one by one and attach to the new burner OR record where each wire goes first
remove the old burner (2 screws) and attach the new burner
screw down the stove top
try the burner - when it does not work flip the power breaker back on and then try again
bask in the joy, admiration and wonder directed your way by various family members
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Homosassa, FL
- Parts Used:
- WB02X33180
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Oven will not heat
As many people have encountered, my oven would not heat but the igniter would be bright orange and glow! Over time, the igniter wears and degrades causing oxidation to the surface. This cause the igniter to fail and operate at a lower current level, below 2.8 amps! Normal igniters operator over 3.0 to 3.1 amps. When is happens, a low current igniter does not have enough input to the control valve to tell the valve to open to allow gas to flow over the igniter to light the oven, thus heat the oven! This has got to be the NUMBER one reason for an oven not heating!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Lexington Park, MD
- Parts Used:
- WB30T10099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
cooktop inner ring did not work
Dear PartSelect:
I am very impressed by your service and company. My order arrived in less than 24 hours. It was a perfect match and is currently in service. I am very satisfied with the entire experience and will use your company again.
I simply opened up the cooktop with a screwdriver and disconnected the wires to the affected burner. After the part arrived, I reconnected them. I had to swap over two brackets from the old burner, so don't throw it away until the new one arrives. It went back together very easily and worked immediately.
Matt Brennan
I am very impressed by your service and company. My order arrived in less than 24 hours. It was a perfect match and is currently in service. I am very satisfied with the entire experience and will use your company again.
I simply opened up the cooktop with a screwdriver and disconnected the wires to the affected burner. After the part arrived, I reconnected them. I had to swap over two brackets from the old burner, so don't throw it away until the new one arrives. It went back together very easily and worked immediately.
Matt Brennan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Pleasant Valley, MO
- Parts Used:
- WB30T10099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Two stage burner was not working on the outer part of burner.
Locate breaker box and turn off breaker to stove. Removed the two screw in front that hold the top in place. Raised the top and supported it with the box the new burner came in. Removed two screws that held the burner in place and the 5 wires one at a time an installed them on the new burner. Put new burner in place and installed two mounting screws. Reinstalled the two screws in the front to hold the top in place then turned the breaker back on and tested burner. Worked great. Received part in 2 days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynda from Burdock, SD
- Parts Used:
- WB30T10099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Small burner not working, outside was fine
Followed directions that I found on the internet and it was easy to remove the old burner and replace it with the one I ordered from you. There was no problems at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TERRY from RICHMOND, VA
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
rear drawer supports broke
Directtions were by diagram only, no written instructions. Drawing was small and difficult to follow but the repair itself was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roosevelt from Waggaman, LA
- Parts Used:
- WB30T10045
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Bad Burner
I simply removed the 2 anchor screws in front of the stove and wrote down the wiring order on the instillation diagram, removed the old burner, removed the two studs, made sure they were installed on the right numbers place them in the new burner, wired the new burner, placed the springs respectively. Placed them in the correct holes in the frame to be sure that the burner was aligned properly. Put the washers on the studs and replaced the frame screws, lowered the cook top and returned the screws to lock the cook top in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BETTY from CYPRESS, TX
- Parts Used:
- WB48T10095
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
I needed an oven with three racks, mine came with two.
just slipped it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from Cave Creek, AZ
- Parts Used:
- WB41T10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
defective oven door seal
pull out defective seal with pliers clean area and press new seal into place making sure the spring clips on seal are completely inserted into door slots push ends of seal into holes in bottom of door
Was this instruction helpful to you?
Thank you for voting!