JBP89SL2SS General Electric Range - Instructions

This was simple enough to repair for me, a relative novice. Just remember you need a nut driver to take the back panel off, take a photo of the existing board so you remember which wires go where, and you definitely need a hair dryer to heat up the sticker on the old board so you can remove it and put it on the new board.

I watched a video of a similar model to familiarize myself with the required steps needed. I opened the back and disconnected the power cord and ground wires connected to the removable socket I then removed the lightbulb and removable socket from the oven interior side. I then removed the defective light socket cup and replaced it with the part I purchased. After replacing the removable socket and lightbulb, the bracket holding the light cover functioned perfectly with the new light socket cup. Final steps were to reconnect the power and ground wires to the removable socket. I then replaced the back cover over the light socket cup area. One word of advise. Be very careful when removing and reconnecting the cables to the removable light socket.

I began by turning off the breaker in the panel.
Slide the oven out into the open area.
Removed 3 screws in order to remove rear top panel.
Took 2 pictures of the wiring location on the PCB
Removed all wiring going to the circuit board total of 8.
Removed 4 screws in order to remove bad PCB.
Remove faceplate from bad PCB (you will need to place this faceplate on the new PCB.

To Install.
Reverse steps above

Easy

Pull range away from back wall. Remove panel behind control knobs by removing the screws that hold it on. Find hot burner light that holds lens. Remove broken part of lens. Insert new lens into hole on front of control panel and into hot burner light receptacle. Replace back panel. Slide range back into place.

popped the new one on!

Pulled stove out to access back panel. Unscrew broken switch/stem. Replaced each wire one at a time to make sure they went in right spot. Screw in new switch. Replaced back panel.

Once I opened up the back of the range, the sensor wires where there and burnt just like your info said. One nut to take off in the oven and the sensor came right out and the new one went right in. The oven works great, cooked the turkey today. The worst part of the repare was the cleaning behind and under the range, it hasn't moved since it was put in 6 years ago. Very pleased with PS.

Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!

replaced oven clock control ref maintenance manual, 4 screws and 8 wires. plugged in new control and op checks good.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Really easy fix. Unplug oven. With a 5/16 nut driver take the 5 screws out of the center long tin cover and remove. Unplug little white temperature sensor plug located between broil heating element. Open oven door and remove one screw holding temp. sensor using same nut driver and simply pull out old sensor. Install new sensor. It's that easy. No more f2 been working like a champ!!!

Removed 4 screws from back panel, disconnected small electricsl connector from sensor, removed one mounting screw from sensor inside oven,pulled wires through and removed old sensor. Fed wires for new sensor through and connected electrical connector, installed panel, installed mounting screw on sensor and checked oven, worked like a champ. Took 5 minutes.

pulled these off and pushed off the new ones. This company is great - knobs fit - good price - stove fixed.

Parts arrived in record time and the right parts. The detailed diagram was so helpful in finding exactly the part I needed to order. Was so easy my girlfriend with no mechanical or electrical experience completely helped me through the entire project. She secured the electrical breaker to the range, and I had the top back to the oven removed. I showed her how the little white box simply slides off the lens cover, then replaced the new one in the holes and slide it back on. Secured the back and she turned on the breaker back on...and all lights work. Thanks for making this project easy, simple and quick.