JGBS23SEH2SS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jeff from League City, TX
- Parts Used:
- WB34K10010, WB34K10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Drip Trays lost finish due to use
Removed grates, lifted old drip pan, cleaned well and put new drip pans in. Simple and looks SO MUCH better!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from North Las Vegas, NV
- Parts Used:
- WB16K10070, WB16K10055, WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
carbonized burners
Replaced all four
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robbin from Somerville, NJ
- Parts Used:
- WB34K10010, WB34K10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed new burners, gas tops and grills for hotpoint range
Customer service was above excellent! Parts delivered quickly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from Brooksville, FL
- Parts Used:
- WB34K10010, WB34K10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Pans were old and looked it!
The repair was just to exchange however, I am still shocked with the delivery. I ordered one day and they were delivered one day later. I was amazed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- glen from felch, MI
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
uneven flame and sputtered, burner was not useable
Simple to correct 1. lift off grate 2. lift off burner cover 3. lift off old burner. 4. replace burner, cover and grate. took 10 seconds. burner works perfect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Alameda, CA
- Parts Used:
- WB20K8
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
With the oven dial at OFF, the oven would turn on by itself every 5 to 10 minutes and it would heat up to about 100F and shut off.
Unplugged the range. Took out all the necessary screws and lifted up the cooktop cover. Unscrewed each gas tubes connecting to each gas burner's dial to allow more working space. Pulled out the old thermostat, installed the new one. Put back the gas tubes and all other necessary screws. Plugged the range and tested out the new thermostat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pamela S from Chesterland, OH
- Parts Used:
- WB20K8
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven Heating Too Hot, More Than 100 Degree Beyond Setting
Replaced the oven thermostat and calibrated the new thermostat by adjusting the temperature setting knob. Instruction I found on-line were very helpful and the repair was moderately difficult. Trickiest part was threading the new thermostat into the oven. Total repair time about 1 hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vicki from Irvine, CA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced damaged oven rack
I ordered the oven rack on a Tuesday and received it the very next day - was wowed at the service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Houston, TX
- Parts Used:
- WB16K10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace medium burner for gas cooktop
Very easy to remove grates, burner cover and remove old burner head. Very simple process, but surprised that there was no efficient way to clean carbon deposits from my old burner. Burner video instructions on line insured I installed the new burner head correctly (actually, pretty hard to get wrong), and burner worked correctly immediately. Will likely replace other burners in time as the new one is so "silvery" colored compared to my other burners.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harriet from Jacksonville Beach, FL
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Open door. Put racks in.
nothing to it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Ogdensburg, NY
- Parts Used:
- WB16K10055, WB29K10001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Stain/polyurethane dried on burner head & cap
Lifted both pieces off and placed the new ones on,turned on the burner and it worked as it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BETTY from CYPRESS, TX
- Parts Used:
- WB48T10095
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
I needed an oven with three racks, mine came with two.
just slipped it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from harrisburg, PA
- Parts Used:
- WB20K8
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Would Not Turn Off
I read the instructions from other peoples repairs. One note: unplug stove, and turn gas off, remember where wires go. I didnt have to remove top of stove completly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Burlington, OK
- Parts Used:
- WB20K8
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven Would Not Turn Off
Opened up the top of the stove using a screwdriver. Lifted it up about 3 inches and legs popped out on each corner and held it in that position. Traced the wire to the back and down to the oven. Pulled new thermostat along that route. When I got to the back it was a little tricky moving the thicker end around and down into the hole without removing anything from the back- but I did manage to do it. I then unhooked old thermostat from 2 clips, inserted new one and then went to the front and unsrewed the 2 small screws behind the oven control knob. Magnetic bit on screwdriver is a must! Pulled it back and removed wires one at atime and put onto new unit, then screwed it back in place and replaced knob. Plugged it in and turned it on. It came on ,stayed lit. Turned it off and it stayed lit- surprised me. . . . . . 25 Seconds or so and it went out. . . . . Job done!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from Watervliet, NY
- Parts Used:
- WB35X37973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Forgot to remove the heat shield from the old part.
Husband actually did the repair, It went really well except he forgot to remove the heat shield from the old part to attach to the new bottom. (His mistake!)
Was this instruction helpful to you?
Thank you for voting!