JCS968BF3BB General Electric Range - Instructions

I unfastened the three 1/4" rear screws, then the two support screws on top. I pulled the old element out,( plenty of slack wire luckily). disconnected it from the bayonet-type connections, then attached the new element. I secured the new element using the 1/4" screws. Bingo!

1- opened oven door
2- unscrewed 2 screws underneath top with a socket wrench
3- unscrewed clips that held burner
4-used needle nose pliers to pull off wire clips off old burner
5- placed wires onto new burner
6- opened clips to make it easier to reinsert burner
7-reattached burner
8-Replaced top

The hardest part was unscrewing the 2 screws that held the top in place due to the position of the screws

Pull range out of the "hole", and spin so that back of range is accessible. Remove cover over top "control area" on back of range. (Four screws that happen to be the same size as the magnetic socket that holds the interchangeable tip on a cordless screw gun. Simply remove this tip, and use the tip holder as a magnetic nut driver!). Remove the knob by pulling gently straight off. Remove black plastic retaining nut under where knob was. Inside are two small screws that hold the switch in place. Remove these screws with a magnetic screwdriver (If you drop these screws and lose them, you'll have a hard time finding them. Very small!!). Carefully follow enclosed instructions to move the wires from the old switch to the new switch. Put back together in reverse order.

Disconnect the power to the oven at the main breaker panel. Open the oven door to the first stop (not all the way open) and pull straight up to remove the oven door from the hinge. Using a 1/4" drive ratchet with 1/2" extension with 1/4" socket, remove the 1/4" sheetmetal screw holding the temperature probe at the center of the broiler mounting plate. Remove the two 1/4" screws holding the broiler mounting plate. Remove the two 1/4" screws holding the broiler element at the ceiling of the oven. Pull the broiler element out from the back of the oven and there should be two electrical connectors at the back of the broiler element. Pull the electrical connectors off of element. Replace the element and re-install in reverse order.

The first thing was to watch U-Tube . The replacement burner was being
replaced in a GE glass top range. Exter tools were required than depicted
in the U-Tube project. The project overall was not dificult for me however I was a general contracter for over 25 years

Very simple. Remove one screw and carefully pull the sensor until you see the connection point. Remove the old one and snap the new one in and guide the wire back and reassemble the screw. Be sure to remove the oven door for easy access.

This door required a lot more screws to be removed in order to remove the inside window assembly. I counted a total of 19 screws. That is why the estimated time is 30-60 minutes.

- remove door from range following the basic guide to removing any range door.
- place door on work surface with the outside facing down.
- remove three 1/4 socket screws from bottom and two star screws on top.
- Flip door over, remove outer door panel and set aside.
- There will be a separate pane of glass that needs to be removed. Remove 1/4 socket screws holding glass and set aside.
- Slide door over your work surface edge so you can remove the star screws holding the door hinges (from underneath). You could flip the door over but the door would have to be flipped back once the hinges were removed.
- Remove the remaining 1/4 screws holding the aluminum shielding.
- Remove the shielding being careful not to disturb the insulation around the window.
- Remove the damaged window. Take note of the writing and orientation on the aluminum window frame. (upper right if hinges were on the bottom)
- Set the new window in its place.
- Reverse the process by replacing the aluminum shield, hinges, than internal glass pane.
- Set outer door on top and holding everything together, flip door.
- Tighten the two star screws on top and the three 1/4 socket screws on the bottom.
- Replace door. Don't forget to lift up those hinge tabs before trying to close the door.
All done. Pat yourself on the back for a job well done.

had to remove the oven from the wall. once i realized that i had to take the side wall brackets off before removing the oven it was quite easy. then just had to remove oven door and slide the unit onto a chair while replacing the sensor. put it all back in and the wife was so happy to have her oven back she made me a batch of brownies. yum.

I pulled out the drawer and inserted the new support. This one inserts into the back of the drawer as opposed to the sides. I had ordered two of the replacements even though I only needed one and decided to replace both. I think it was a good move as the drawer works better than when we first got it. Just one simple screw made it complete.

Oven door must be removed briefly while old false bottom is slid out and replaced with new one. Oven door is easily replaced and oven is like new.

First I removed the 4 screws that hold the element in place. I then pulled the element out about 3 inches. I removed the sensor and disconnected the connector.

. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two plugs.
plugged in the new element and screwed it in place

Just like everyone else it was a simple r&r. However, when removing or installing wire clips I make it a habit to hold the ends with needle nose to prevent any: "snap!" ooops! However to prevent burning the element in the first place, it is strongly suggested to push that broil button twice so that it is set to low temp. It is too easy to use the high setting which will shorten the elements life by 40 - 60 %. Also, keep the oven door partially open when using the broiler. Like the manual tells you!!!

pull out stove, unbolt old temp sensor inside stove with 1/4 nutdriver, go to back of stove and take off cover and unhook sensor and hook up new one, put all back together and slide stove back in place.

turned off power to oven; pulled out old bulb (unscrewed glass cover to access). Noted the direction of the electrical prongs when pulled bulb out... and inserted new bulb. Turned back on power to oven - bulb worked