JGBS07PEA6WW General Electric Range - Instructions

To: Remove.Four(4)nuts. Six(6)screws. Two (2) clips. To:Reinstall reverse process. "Very simple stright forward, and most enjoyable."

slid the old ones out and slid the new ones in. done

I removed the original gasket clips with pliers. I installed the new gasket by aligning the clips with the holes around the door and pressed into place. Easy fix!

replaced lights in refrigirator and freezer

1) Turn off power at circuit breaker panel
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and discard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!

I moved to an apartment where the past tenants did not take care of the stove. I think this stove is 10+ years old and looks like it was never cleaned in all of its existance! I cleaned everything really well with oven cleaner and lots of scrubbing. The stove looked brand new except the burners! I couldn't take it anymore so I ordered new ones. The burners came in less time than stated. I opened the box, took the burners out, lifted the oven hood and just placed them right where the others were. There are no tools needed it pretty much just gets placed down in the appropriate spot and that's that! No directions or tools needed. My stove looks awesome now!! When you first use the burners, you will probably need to place a match or lighter by the burner to get the fire going. After that, it lights perfectly every time.

First just unscrew each natural gas jet and install the propane jets. if they are hard to come off just turn your wrench back and forth first until the jet turns with your fingers. Then open the oven and take out the racks. In the bottom back of the inside of the oven there is a screw on each side. Unscrew both screws lift the bototom plate of the oven and slide it back about 1/2 inch then lift out of the oven. Move the 1 screw covering the heat shield from the oven jet. Then light the top burners and turn them off just to get the gas flowing. Also light the pilot in the oven, then light the oven. To convert the oven from natural gas to propane all you have to do is adjust the jet while the oven is lit. turn the oven jet ubtil there is a blue flame with little or no yellow tips on the flames.

The repair was somewhat easy, it would have been easiere if I had figured out the right part in the first place! Replacing the Thermostat is a simple task and actually only took abut 10 minutes. The harder task was replacing the glow bar in the broiler area! What a pain! The part had the same gender connector as the existing wiring. Had to cut the connectors off and use ceramic wire nuts... should be simple but the wires on the replacement part were about 1/2 inch too short! After some creative manuvering and about an hour of cussing out the OEM part manufacturer it went together and worked OK but I suggest before trying to solve a problem like this remember the basics... always check the obvious first!

Found the Model information under the bottom drawer. Googled GE Range and rubber, found this vendor. Amazing, the replacement gasket was exactly as the original. Took the old gasket off with needle nose pliers, there were small metal clamps that had to be pinched together. Once the old gasket was off, the new one practically installed itself. Woman Power!

Baking is MUCH better now!

had to drill hole bigger to fit electrode

Popped off old gasket and some retaining clips stuck but were easily removable. New gasket pops right in, super easy. Fits like new.

On a 18 year old electric GE range: amazing not the exact handle but it does fit perfectly and looks great. If your somewhat handy this is very easy and can be completed in less than a half hour. Save the screws from the old handle, they can be used again.

Very was ti replace racks and knobs. Very fast mail service

New bake tube fit perfectly.

You need to remove the knobs and remove the panel where the knobs are connected.

You also need to remove the display panel front to gain access to the where the electrode wires attach.

The other screws are readily visible. It's about 30 screws that need to be pulled.

The adapter put on the electrode can be pulled off with needle nose pliers and a small screwdriver, if the adapter does not fit through the opening on your stove. Just put the adapter back on after you snake the wires through.