HMV24CEWABB General Electric Range - Instructions

I pretty much followed the youtube video posted under the part that I needed. Turned off electricity to that area of the house. Unplugged stove. Took out the old sensor, pushed new sensor cord through the back hole. I did put a small amount of tape,so I could pull it through from the back better. It was impossible to get the clip disconnected in the back and the new clip didn't match up correctly anyway. Ended up having to cut the wires and strip them. I twisted them together and put on the ceramic wire nuts on. Reversed ever thing I did and F3 appeared. Looked that code up on internet. It was from an open or shorted oven. Suggested I check the connections. Pulled stove out again, unscrewed caps on wires and noticed the sensor's wire had another cloth type coating on it. I gentle cut that off, twisted and capped wires again. Plugged in oven, turn on electricity, and tried out stove. Everything is working just fine. Everything took a little longer because this was first time doing this type of repair.

Had to take back off of the door to get to screw that held the broken piece of handle before installing the new part. Then had to put the back on the door and slip the door into place.

Took off the inside ( this allowed me to clean the glass) panel. Removed the two end parts with a screw driver. Replace the parts and we were good to go.

just replace the end cap with a new one all that was involue was to screw the new one in took about ten minutes and job done better than buying a new stove when the stove is still just like new. thank you for your on line help.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

replaced lights in refrigirator and freezer

I attached the end caps to my existing handle, but had to squeeze the parts together very hard to get them to mesh to the correct distance of the holes. I removed the screws holding outside frame of the oven door. I then opened the door fully, propping it up on my knee and removed the inside end cap screws. Placing the handle in position underneath the propped door, I attached the screws. Lastly I reassembled the door.

Watched the video on the PartSelect site. Could not have been an easier repair and I saved the cost of a service call - probably saved at least $100 - $150 in service call and I can only guess what the labor cost would have been. Will use this business again for other appliance repairs on my older stove, washer, etc. By the way - the official Kenmore site said this part was no longer made and unavailable --- Thank you PartSelect for having the part and saving me the cost of buying a new stove!

With multimeter checked resistance of oven sensor. Specs called for 1100 ohms. It was off by 27 ohms. The sensor from Part Select had exact wire connection as original. Then just matter of undoing old and reconnecting with new one.

One unsatisfactory event. I asked Part Select why my clock did not work or light up(timer works ok) . Answer was: sorry we have no time to help you. That soured the otherwise happy experience.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Very easy, didn't even have to take the oven out of the wall. Will use this site again.

Took door off of hinge
Removed 6 screws from bottom of door
Removed glass
Removed screws from side of door
Removed door from frame
Replaced the end caps using exisiting screws
Put door back together in reverse order
Pretty easy but simple instructions would have made it a 15 minute job instead of 30

Open door lift door off hinges lay door face down on flat surface remove 6 phillip head screws 3 on each side lift housing out of door case remove end knob phillip head screws installed one knob insert bar attch second knob and tighten screws lay housing back into casing attach screws doing one at a time on each side slide door back on to hinges and test operate, you are done!

From what I was able to find info on I was to take out 5 screws 3 on top and 2 on the bottom then the inner oven box is suppose to pull out a bit to take the old gasket off and put the new onw on the box was so rusty it would not pull out so I was able to get enough of the box out using a large screwdriver the lip of the gasket tucks behind the box. I ended up using a small screwdriver to work the new gasket behind the oven box. The door now needs new springs the tension on them is not strong enough to pull the door shut the way it should there's still room to push the door into new gasket.

Easy