JBP61DA1WH General Electric Range - Instructions

While I appreciate all the various parts available from PartSelect, I was disappointed that the only heater element that was approximately the right size and shape for my wall oven had push-on prongs. My original was screw-on.

Thus, I had to (very) carefully drill through the somewhat thick metal tabs to get screws into them. This meant holding the tabs with a pliers while I drilled them out to make sure that I did not break off the tab. Then, I increased the hole size by using increasing diameter drill bits. I let the screws self-tap, but again this was done carefully to avoid breaking off the tabs. Finally, I found that the part of the new heater element going through the back wall of the oven was an inch or so longer than the original. This did not seem to cause a problem of overheating outside the oven. At least not so far!

I followed the easy instructions and everything went well. I had the new switch installed in about 30 minutes. My wires were different colors than on the instructions but it was still easy to figure out where the wires went on the new switch. Just do not be in a hurry and make sure you measure before you break off the extension bar. My knob fit on the new switch without any of the parts that came with the switch.

It was so simple looking, I had it shipped to the tenants of the house. They swapped it out easily, and were happy to get back to baking.

Removed all screws holding top of range and two screws holding latch mechanism. Opened top of range; disconnected two wires and removed damaged part. (Replacement was delivered within 24 hrs of order! ) Removed plastic tip from damaged part and installed on replacement part. Replaced damaged part. Attached wires. Attached latch with two screws. Closed top; secured with screws. Latch functioned perfectly.

Of course the first thing is to turn off the breaker, Unplug the appliance, pull the two electric feed wires off the old element. Then remove the four screws that hold the fan guard in, After that the two screws that held the Bake Element in place. Then reverse the process to install the New Element. Took about twenty mins. from start to finish. Just Like New. And thanks to Parts Select for their prompt service, Had the new part in two business days.

popped the new one on!

First I shut off the power at the power box. Second I removed two screws in metal plate. Third I unplugged the two wires. Repeated steps backwards and it works great.

saw when heating the stove up the bottom element wasn't getting hot. got part number and looked up online and ordered

Your "virtual repairman" was fantastic. I would have purchased the wrong part without trhe diagnostic service. It said that 53% of the time the infinite switch was the problem. In my case it was 100%. Why I put up with this problem for 6 years I will never know.

Repair job was easy but longer than the 15 minutes that it said it would take.

First of all I did this repair because the wire to the burner shorted out. I did the wire portion first - only then did I know I needed the switch kit. (The burner was operating while my old swithch was OFF). The first (wire replacement) repair took about 10 minutes - I followed the guidance on this web-site. The second repair (The switch) took about 20 minutes. The switch ws not the same as the original. Just be careful to mark each wire as you remove them from the old switch's posts. The posts on the switch are marked and you need to place them on the like-marked corresponding posts on the new switch. All is well, my burner is operational.

1. The infinite switch had several knobs which would fit the switch shaft. Read the directions included with the switch in order to have the shaft fit the proper knob. You can break the shaft with two pairs of pliers. 2. Move the stove away from the wall and unplug it. 3. Remove the 1/4 screws from the back side of the stove and remove the back panel, exposing the switch. 4. Remove the wires one at a time and put them on the new switch. The terminals are L1, L2, P, H1 & H2. The Pilot (p) has a smaller terminal so you don't get it mixed up. Generally L1 is black, L1 is red, P is yellow, H1 and H2 can be blue, brown, yellow, orange or one of these colors striped on a white wire. 5. Remove the old switch from the stove and be sure to save the two mounting screws. 6. Position the new switch so that the side of the switch marked "top" is on top. 7. Install the screws on the new switch and put the knob on it. 8. Carefully test the burner. 9. Unplug the stove and put the back cover on.

I ordered it on line and it was easy to fix, I had it done before my husband came home from work. I just undid the old one and pushed the new one on. I have to stay ordering from here was alot cheapier

Removed both racks, removed two screws holding element in. Removed two screws holding wires on element. Drilled holes in new element where the push-on connectors are attached so I could attach the oven wires to the new element. Attached the wires and screwed the element to the oven. Fit perfectly and the temperature of the oven matches the control knob finally!

Thanks.

I ordered to correct part from PartSelect with relative ease given I know nothing about oven repair. What's even more amazing, my wife who is not mechanically-minded, took the element home and replaced the broken one in 15 minutes with nothing but a pair of pliers. We live 22 miles from town so a repairman would have cost over $100 just to show up. Total cost = $36!

I first read the repair stories on this website. I turned off the power to the range in the power box. I removed the 2 screws, pulled out the old heat element a little, then disconnected the wires from the connectors. I just reversed the steps to put the new one in and viola. Really simple. Parts came really fast too. At first I ordered the wrong part b/c I didn't look up the part using the model number, I just went by t he picture and the manf. name. I returned that and got refunded promptly, so make sure you order by model number b/c parts are made different for each appliance model.