JGBP83BEJ2BB General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- glen from felch, MI
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
uneven flame and sputtered, burner was not useable
Simple to correct 1. lift off grate 2. lift off burner cover 3. lift off old burner. 4. replace burner, cover and grate. took 10 seconds. burner works perfect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rachelle from Airmont, NY
- Parts Used:
- WB03K10141
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing knob on range
Order came very quickly and was the perfect fit. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Las Cruces, NM
- Parts Used:
- WB16K10035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Oven not heating
Installation was very quick and simple. Removed wire connector for the igniter then hex screws for the bake tube. Attached the new igniter to the new bake tube and reinstalled in oven. 15 mins. I took the extra time to clean the oven pan and heat shields. Removed old charred baking spills and grease buildup. Oven is 12 years old and working like brand new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Grass Valley, CA
- Parts Used:
- WB16K10035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven wouldn't heat up.
Replaced the burner and igniter after watching the repair video provided by Partselect. I was pleasantly surprised when the parts came the very next day. It was so easy and the igniter plug matched perfect. My wife wanted to hire a repair man but I did the repair and saved a bundle on the labor. I couldn't be happier about my purchase.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Louisiana, MO
- Parts Used:
- WB16K10035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven would fill up with gas before igniter got hot enough to lite it
Remove bottom drawer,open oven door,take oven racks out,use flat tip screwdriver to remove two screws in back of oven. Then remove cover over burner and igniter.Reach under oven and unplug igniter,while down there use 1/4 inch nut driver and remove two screws holding burner. Then remove one screw inside oven in front of burner. Pull burner and igniter up and out of oven.I did not unplug stove or turn off gas some people may want to,if you have to move stove out to work on it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from Watervliet, NY
- Parts Used:
- WB35X37973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Forgot to remove the heat shield from the old part.
Husband actually did the repair, It went really well except he forgot to remove the heat shield from the old part to attach to the new bottom. (His mistake!)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Redondo Beach, CA
- Parts Used:
- WB35X37973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
My oven bottom got rusty
I removed two bolts at the rear of the oven bottom. I pulled the old oven bottom out, and put the new oven bottom in. I put the two bolts back in and voila it looks like a new oven. Done in less than 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Ogdensburg, NY
- Parts Used:
- WB16K10055, WB29K10001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Stain/polyurethane dried on burner head & cap
Lifted both pieces off and placed the new ones on,turned on the burner and it worked as it should.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Brandenburg, KY
- Parts Used:
- WB08T10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Oven light wire broken, damaged socket
Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.
Was this instruction helpful to you?
Thank you for voting!