JDP39WW1WW General Electric Range - Instructions

This was really easy considering what it would have cost to have a repair person come and do it - not to mention the wait time. I had to hunt around a little bit to find the right socket, but once I had that, I unscrewed the bolts in the back and slide the element out. TIP: make sure you turn off the electricity!!!!!!!!! The wires were a little stuck, but the oven is 11 years old, so it's to be expected. One of the wires came off behind the oven, but I used needle nose pliers and fished around until I grabbed it. I detached the wires, attached the new ones, turned the electricity on and it's been baking Christmas cookies ever since. BTW - the part came in 3 days. I was sooo happy I didn't have to wait for a repair person. Thanks for all of you who posted your comments online. That was just the encouragement I needed to try it myself!

Removed two scres that hold element in Place. Pulled out element about 3" and removed wire disconnect. Re-connected new element and re-installed mounting screws. Very easy. Parts were delivered promptly. Great service!!!! Thank you Parts select!!!!! Saved me a trip to Sears to purchas a new element or Stove.

first i unplugged the stove to disconnect all power. next itried using pliers to unscrew the screws and was having a hard time so hubby got the adjustable wrench and it was much easier. after taking out the two screws, i pulled the element out about three inches and disconnected the element from the two wires that hold it in place. then i snapped the new element in place just as the old one was and reattached the element to the stove using the two screws. after assuring that element was secure, i turned my oven on to 300 degrees and voila!!! we're cookin again!!!

the only challenging thing realizing that the screws in the back weren't for a screw driver, they were for a very small wrench. Since I didn't have such a tool, I just used vice grips. It all went well though. The oven currently heats to 400 degrees in 7.5 min. I am quite happy.

After noticing it needed replaced I went to PartSelect, put in model/serial# and order that easy. It was here the next day. The oven was fixed. Now back to baking...thanks PartSelect.

I really like my repairman, but prefer to do it myself. PartSelect rocks...reasonable prices, really fast shipping AND online repair videos keep me coming back. The repair was exactly as the video described, but one of the wires came loose as I was pulling the element through. I thought I'd have to tear the stove apart to get to it, but luckily, all of the wiring is contained in a raceway that runs along the back of the stove. After removing it to expose the wires, I would recommend doing so instead of trying to pull the wires through as the video shows. In doing so, the terminal connections are readily accessible and it's much easier to remove and install the bake element without having to worry about feeding the wires through at the same time and running the risk of damaging them. Overall, a very simple, quick repair that saved me a $50-75 service call.

As others have described, the removal of the old bake element is easy, just undo screws in the mount holding it to the inside wall of oven and pull out, then disconnect wires.

The first thing I faced unique is that some of the old element melted on the walls of my oven. After scrubbing extensively, it was obvious that the majority of the melted element was permanently fused with the oven wall--although it doesn't seem to have affected oven performance so far.

Next since my range was made in 1982, the replacement bake element didn't exactly fit my unit. Several adjustments had to be made. The size and fuctionality of the new bake element matched my oven, however the wire connections and the oven wall mounting bracket and the spacing of the two ends of the element as it went thru the oven wall were very different and required extensive modifications.

I used the old mounting bracket from the old melted element to attach the new element since my oven wall opening and mounting holes matched the old element mount--NOT the new element mount. This required removing the old mount from the old element by means of a vice, hacksaw and wirecutters. It was necessary to examine the old element mount very carefully before I hacksawed it off the old element as it must be reconfigured onto the new element. It will be bent up somewhat while removing---be careful.

Then I reattached the old mount on the new element. This required carefully bending the new element ends to receive the old mount as they were spread too far apart in the new element configuration. After much trial and error bending with several types of wirecutters the old mount was secured to the new element and installed into the oven.

Now a new problem appeared--the element ends now stuck too far into the back wall of the oven, making them dangerously close to touching the exterior of the rear of the oven and remember these are bare, hot electric connections! Much time in trial bendings and repositioning of the new element with the old mount finally resulted in a successful mounting with the old mount and the new element in a way that safely kept the bare wire connections within the rear oven walls.

A final problem was encountered when the new element came with slide-on wire connectors while my old element had screws and holes to connect the wires together. I found a drill bit the size of the required screws and drilled holes in the new element's wire slide-on connectors so that I could use the screw connector system of my old element to connect my new element's wires together. It all worked and the oven is functional.

Turned power off. Removed two screws holding the element. Pulled element out 3 inches, disconnected the two wires, pulled out old element, connected wires of new element, replaced screws. Turned power back on. Eureka!! the oven heats again. :-)

After removing the screws holding the element in I disconnected the wires and attached alligator clips to the wires to keep them from pulling back inside the holes. I would have had to pull the stove out and removed some covers if they disappeared through the holes. After getting the part number off of the old element, I ordered a new element from Partselect.com and received the new one in less the a week. Reinstalling the new element took about 5 minutes.

Removed oven shelves (30 seconds). Removed 2 screws holding broken element to oven (2 minutes). Pulled broken element assembly out & removed 2 wires attached to element (1 minute). Connected wires to new element (just push them into place) and mounted new element with the 2 screws (1 1/2 minutes). Turned on oven element to test & since I was so tired from all of this 5-minute activity, I rested.

Al S.

First I switched the fuse to the oven had no power and then I removed the old element and wiped down the inside with a damp towel.
I then attached the new element and then used the screws to attach the element firmly into place.
I then restored power by switching the fuse back and then burned the element to remove and chemicals and then done

Took out the hexagon screws, used pliers to pull the connecting ends apart, slid in the new element in to the connecting slots, reattached to screws, turned on the oven to see if it would heat up and it did. It was really easy. I had waited for a week to get the part from my local Sears parts house. You sent it out and I had it in 3 days. They still don't have the part. Thanks so much.

Cut power to oven from breaker box. Remove two retaining screws using a nutdriver at rear of oven. Slowly pull Bake Element from rear of range exposing connector clips. Disconnect at clips from oven wiring. Connect new Baking Element to wiring connectors. Push new baking element into rear of oven. Reconnect baking element using original screws with nutdriver at rear of oven. Turn on power to oven from breaker box. Job complete in 10-15 mins.

I removed the two screws with a nut driver, pulled the element out far enough to expose the connection point and disconnected the electrical clips. Upon receipt of the new element I did those things in reverse order and it worked great.

This repair was idiot-proof. Removed 2 screws, unplugged the old part, plugged in the new one, and replaced the 2 screws.
Literally a 2 minute repair!!