JBS03GV5 General Electric Range - Instructions

1. Bought replacement part said to replace old switch.
2. Pulled old switch out.
3. Replacement part did not match. Would have to take entire switch panel apart to change to this part.
4. Multiple-part instructions very poor. For my switch unreadable.
5. Old part was "push to turn". New part was not.
6. Knob did not fit new switch. Old shaft was "D" shaped. New is square.
7. Gave up. Need to call repair shop.
8. Hope this helps.

Removed old surface burners and replaced them by plugging in the new surface burners. Now they work GREAT! Parts ordered and received with-in 3 business days. Fed EX delivered parts in good order very quickly. We recommend PartSelect.com

Replace part an wires

First shut the power to the stove,then had to slide the stove out so I could get at the back to remove the panel screws.Once you have the back off remove the knob on the front.Under the knob is 2 phillips screws that you need to remove.Next I took the new switch and matched up the wires to the old switch.Reinstall is the reverse.Once the switch is in place you must remove the excess shaft to match the length of the old one.This is done with the use of 2 pliers,you grasp the shaft with both pliers and snap it off where you need it.The kit comes with spacers so you have got to match up the right one so the switch is solid on the shaft.This finishes the project,next turn the power back on and check that all is working ok.Job finished.

When I pulled the old element out only one of the wires was visible, the other wire was still connected and after pulling a few times it came out , but the wire connector wasnt visible and I had to dig around in the small opening to find it (2 hours worth of digging and pulling) I finally got a hold of the wire and pulled it through and was able to connect it to the element, had to bend the metal around the opening to be able to get my finger in there and find the wire, The screws that hold the element in place wernt the same as the original so i just have it pushed up in place but it seems to work ok , took way longer than i thought it would.

Unplug coil, remove pan - place new pan, plug in new element and bingo. Took approximately 30 seconds!

Got all my parts and tools ready. Sat on a stool in front of oven. Swapped out old with new. Not bad at all.

Surface element easily unplugged and removed, drip pans lifted out, New drip pans inserted, New 8" surface element and present 6" surface elements Inserted and plugged in.

Removed existing surface element and replaced with new element.

P.S.

Part Select service was excellent.

took 2 screws out removed old element, put new element in and put the 2 screws back in. All worked great and I baked bread that same day. The service was fantastic, and $40.oo cheaper than the appliance store I checked with.

OK, I put the drip pan under the burner. Without a single problem.

I went online to find the part. I also found a how-todo it self installation instructions. So, I thought I would try it. I pulled the stove out and unplugged it. It took me 2 days to try and remove the screws. They wouldn't budge. On the second day, I was about to give up. I tried to loosen the screws again. It finally moved!! So, I kept at it. Took me about 10 mins on the first screw. Then another 10 or 15 minutes on the second one. Once I took the screws off, I didn't know how to remove the wires. I kept picking at them for about 5 minutes, and it was easy then. Removed the old bake element. Then connected the new element wires, put the screws back in (not tight). Plugged it up and tested it. It worked!!!!!! I've never did anything like this before. If the screws wouldn't have been so hard to remove;it would have went a lot better.

Because of the superb pics and descriptions on the Part Select site, I was able (with NO range model number) to order the correct range element for beloved son's stove. He plugged it in in 3 seconds, works great !

I removed the screws holding the element in place and pulled it out, then pulled the wires from the element out. Very easy. When I got the new part, it seemed like it would be simple. I plugged the new wires back in and started to push it in place to screw it in. Unfortunately, there was a big spark and everything died. I was afraid I had crossed the wires, and I'm still not sure how one is supposed to tell which wire plugs in to which holder in the oven. Luckily, I discovered that I had simply blown a fuse. Problem solved, everything works.

Removed the two screws which mount the element to the back of the stove.
The old element had screws connecting the wires to the heat element. The new element needed female electro-terms, so I crimped the appropriate electro terms on. If you need to do this make sure you use the correct electro-terms based on the wire size from the stove.
Installed new element in 2 minutes.
Parts Select had the part here within two days with standard ground shipping. Very impressed with service.
A clearer description of how the part connected to the wires from the stove would have been helpful.