Models > JBP21WA1 > Instructions

JBP21WA1 General Electric Range - Instructions

Jump to:

All Instructions for the JBP21WA1
121 - 135 of 174
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
James from Nashville, AR
Parts Used:
WB21X36771
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
R had ight front control made loud noise when contacts opened.
This is twin oven range with controls at side of upper oven. Control panel was fastened with screws at top and bottom. Range has built-in hood at top which had to be disassembled to reach top screw. Once had access to top screw, eaisly removed control panel and replaced control. New control had identical connections as old control so only had to install it, break shaft to correct length, and use proper shaft adapter for knob. Remounted control panel and range worked perfectly. This would have been a very quick job except for having to deal with the built-in range hood.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Barbara from Edwardsville, IL
Parts Used:
WB23X5340
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Oven Sensor Replacement
The part was just like the old one and would have been an easy fix except our range suffered from a lighting hit. The clips had melted together. Called a dealer and asked about a new wiring harness. He said in those cases just cut the clip off and hard wire with wire clips,or firecrackers. We used wire nuts and taped all together and the oven works just great. Nothing is ever as easy as it should be.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Clifford from New smyrna beach, FL
Parts Used:
WB21X36771
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Burner constantly heated
Good directions
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joseph from Baden, PA
Parts Used:
WB21X36771
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
Front Burner,no control of.
The original controls were different for the small burners and the large burners. The replacement part fits all. Before removing wires, pay attention to writing on new and old control and replace 1 at a time. The hardest part was being sure to cut the knob stem to the correct length. Control works well.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Floyd from Warren, OR
Parts Used:
WB21X36771
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Plastic Insert for knob to long, had to use my bench grinder to cut it down
(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rod from Huron, OH
Parts Used:
WB21X36771
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
rht. front element would not heat properly
I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Leonard from Winter, WI
Parts Used:
WB21X36771
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
element heat wouldn vary
slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting the range back.
Was this instruction helpful to you?
Thank you for voting!
Customer:
THOMAS J from Las Vegas, NV
Parts Used:
WB25X5054
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Light Lens damaged
Required new light lens for oven this type has five (5) of them; only the oven temp light lens was damaged. Ordered from Parts Select.com received item fast in seven days. removed rear guard plate, than oven temperture switch than slid the neon light switch off of the light lens.Lens is removed from the front panel. Installation is reverse order.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Wayne from Houston, TX
Parts Used:
WB44X10009
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Broken bake element
Unplug the old one and plug in the new one. Nice and easy.
Was this instruction helpful to you?
Thank you for voting!
Customer:
frances h from saluda, VA
Parts Used:
WB44X10009
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
element burned out
I disconnected the power to the stove and it was very simple, undid the nuts with socket wrench pulled element out and diconnected the wires.I put the new element back in the same way the old one was removed .I am a 70 year old woman.The great part was the element was shipped out vey quickly! great service
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ronald from Spring Hill, TN
Parts Used:
WB44X10009
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Socket set
Bake Element burnt out
Removed the 2 screws, unpluged the 2 wires and installed the new elment
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from Durham, NC
Parts Used:
WB44X10009
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
oven wouldn't heat
replaced bake elementAndrew W. was helpful getting the right part..
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dorothy from South Daytona, FL
Parts Used:
WB30M1
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
I needed to replace the 6" surface unit.
My GE range is 20 years old, and still going strong. All I needed was to replace the 6" surface unit. After making slight adjustments, it was just a matter of placing the new unit. After finding this Co. on the internet, and checking others, I will certainly order from Part Select again!Dorothy Trakshel
Was this instruction helpful to you?
Thank you for voting!
Customer:
Betty from Fayetteville, WV
Parts Used:
WB30M1
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
the center of the element had broken
just pulled the old one out and replaced with new one. very easy
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from El Paso, TX
Parts Used:
WB30M2
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
heating element would not heat to red hot.
unplugged and installed
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JBP21WA1
121 - 135 of 174