JGB910SEC3SS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Scott from Corinth, MS
- Parts Used:
- WB28K10025, WB28K10024
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
Wife broke gas lines when trying to clean under hood
Removed old line with wrench and attached new line to gas valve first. Then lowered hood to the stop and attached gas line to burners.........very easy and works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Akshay from Bridgeton, NJ
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner had uneven flames
Too easy a five year old could do it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from WINTERVILLE, GA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lights blown out
replaced lights in refrigirator and freezer
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Solomon A from COLLEGE PARK, GA
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The eye would not light
Remove the existing burner and install the replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ESTELA E from HOUSTON, TX
- Parts Used:
- WB16T10046, WB29K10006, WB01K10008
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
No burner
I just put everything on it and lighted match and problem solved! Easy fix!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sally from Bakersfield, CA
- Parts Used:
- WB28K10025, WB28K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
broke tubes while cleaning under top
was still using back burners while waiting for parts (after safety check). I unplugged the electric for the igniters, raised top, installed tubes, checked for leaks with soap solution, closed top, plugged in electric tested burners. Got a big hug and kiss from my wife.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PHILL from SOMERSET, NJ
- Parts Used:
- WB28K10025, WB28K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
the tubes both leaked
replacement was a snap and took only a small adjustable wrench and a flashlight. asome slight bending of the tube was required, but a gentle hand solved the problem easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LEAH from YUMA, AZ
- Parts Used:
- WB28K10025, WB28K10024
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
tube that sends gas to burners broke both left and right front this happen due to opening the range hood to clean inside
I turn gas off to the appliance then I remove the old gas lines and installed the new ones. I did find it easlier to attach the line at the burner knob first then attach it to the burner.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Herndon, VA
- Parts Used:
- WB02K10011, WB02K10136
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Self Cleaning Safety Latch broken
This was a difficult repair because half of the screw on the stove top had to be drilled in order to get access to the device that operates the locking mechanism for the door latch for the self cleaning oven function. Once all the screws where removed it was an easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from FAIRFIELD, OH
- Parts Used:
- WB20T10024
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Oven meat probe broken
This item worked as described. I paid more for this 'oem' probe than the generic 1 because i didn't want to chance it not working as others have reported.
- works great. tested it....snaps in, reads correctly, snaps out.
- works great. tested it....snaps in, reads correctly, snaps out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mohammad from BARTLETT, IL
- Parts Used:
- WB16K10055, WB16T10046
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The old burners were damaged by the prior owners.
The repair was extremely easy. Just removed the old burners and dropped in the new ones. No tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from SOUTH ELGIN, IL
- Parts Used:
- WB16T10046, WB16K10055
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burners wouldn't light
Had two burners on the stove that would not light. Had tried cleaning them but they still did not ignite. Replaced both burner heads. Once replaced. they ignited right away and have worked ever since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAPHNE from CHICAGO, IL
- Parts Used:
- WB28K10025, WB28K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
while cleaning I broke the tubes either lifting or closing the top.
I bent the tubes very slghtly to rech the area of attachment. I first screwed them with my hand then tightened them with an adjstable wrench. It was really simple and fast.
Was this instruction helpful to you?
Thank you for voting!