JGSP23BEW1BB General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from South Bend, WA
- Parts Used:
- WB7X7183
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
The door handle end caps did not fit on to the handle far enough. this caused the screw hole spread to be too wide, Also the new end caps had two nipples outside the bolt holes that the original brackets did not have.
The reason the brackets didn't go on to the handle far enough was there was a molding defect inside one of the brackets. After alot of scraping at the inside of the bracket and lightly tapping with a soft hammer I was able to get the defective bracket on so that the holes lined up to the mounting plate. As for the extra nipples I had two options. Either cut the nipples off or drill some holes in the metal plate that the brackets attach to. I chose the latter. I had to attach the brackets to the plate with extra long screws, reach in under the bracket with a scribe and mark the nipple location on the plate. Then I removed the handle and drilled two holes for each bracket. After some minor adjustments to the holes I was able to attach both brackets and reassemble the oven door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margaret from Cogan Station, PA
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Broken oven door handle. Needed the brackets and screws to repair it.
removed the broken parts and screwed on the new parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cornelius from Hollister, CA
- Parts Used:
- WB7X7183
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
plastic sockets in end caps for connection screws broke off
Very detailed repair instructions on internet made installation of new end caps a job not needing a professioal.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Muskego, WI
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broke end cap while moving range
unscrewed broken end cap, removed from handle and replaced the new end cap
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Milan, TN
- Parts Used:
- WB7X7183
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broken door handle
Pull door from oven and place on flat work surface. Remove bottom screws then the top screws and separate the two halves of the door . Remove broken door handles and replace reassemble door and place back on oven. The hardest thing was to clean the grease out of the inside of the door and get the glass clean to reassemble the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Pflugerville, TX
- Parts Used:
- WB24T10071
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Ignitor on one burner worked intermittently
Cut off power to the cook top and confirm that power is actually off. In my case, this involved turning off a cicuit breaker. Remove all burner control knobs by pulling straight up. Lift off all grates, burner caps and burner heads. Remove two phillips head screws from each burner bowl. Pry each burner bowl up and unhook the ignitor wire. I labeled the wires to make sure I got them hooked back up right. Remove the four burner bowls by lifting them off. Make sure you remember where each goes so you can reinstall them in the right places. Pry up the glass cooktop and lift it off. I took the cooktop ouside and gave it a good cleaning. This plus cleaning around the cooktop and cleaning the burner bowls is what took most the time. Lift the defective switch off and disconnect the two wires. Align the flat in the new switch to the off position. Reconnect the wires and install the new switch on the valve stem. Reinstall the cook top. Reinstall the burner bowls making sure to reconnect the ignitor wires. Reinstall the burner heads, burner caps, grates and knobs. Turn the power back on and make sure everything works correctly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from Schererville, IN
- Parts Used:
- WB7X7183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
broken door handle
repair was easy and the video was very good. My only problem, I had to go buy a tool, I did not have a nut driver.
Was this instruction helpful to you?
Thank you for voting!