JBP19BY4 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- WILLARD from GLOVERSVILLE, NY
- Parts Used:
- WB21X36771
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
instructions could be better
it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clifford from New smyrna beach, FL
- Parts Used:
- WB21X36771
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Burner constantly heated
Good directions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Hamilton, OH
- Parts Used:
- WB21X36771
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Shaft for burner control knob broke off
I flipped breaker off for electic and confirmed that power to the stove was off. I removed the 2 screws holding the control unit in place. Carefully removed all knobs and buttons and pryed the cover for the control unit off. I then removed old part, removed the wired and clipped wires to the new unit. Put cover back on - has some difficulty getting the panel back in place to line up the screws. But after a couple of attempts, was able to line up unit and put screws in place to secure. Replaced all knobs. Turn breaker back on and cooked lunch. Very easy job. Most difficult part was getting panel back in position. I would watch alignment more carefully before I removed in next time. Easy home repair for Women...not sure about my man?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Baden, PA
- Parts Used:
- WB21X36771
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Front Burner,no control of.
The original controls were different for the small burners and the large burners. The replacement part fits all. Before removing wires, pay attention to writing on new and old control and replace 1 at a time. The hardest part was being sure to cut the knob stem to the correct length. Control works well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Nashville, AR
- Parts Used:
- WB21X36771
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
R had ight front control made loud noise when contacts opened.
This is twin oven range with controls at side of upper oven. Control panel was fastened with screws at top and bottom. Range has built-in hood at top which had to be disassembled to reach top screw. Once had access to top screw, eaisly removed control panel and replaced control. New control had identical connections as old control so only had to install it, break shaft to correct length, and use proper shaft adapter for knob. Remounted control panel and range worked perfectly. This would have been a very quick job except for having to deal with the built-in range hood.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cary from hermitage, TN
- Parts Used:
- WB31K10266, WB31K10265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Could not find the proper fitting drip pans.
Got the right ones from you"could not get them at Sears.com". All is well, wife is happy again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- nancy from abita springs, LA
- Parts Used:
- WB31K10266, WB31K10265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
drip pans worn out and rusted
just replaced drip pans. your company response was quick and delivery prompt. being an outdated range, am glad I could fine size I needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from El Paso, TX
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
heating element would not heat to red hot.
unplugged and installed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from Dodge Center, MN
- Parts Used:
- WB44X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
heating element stopped working
Unplug appliance. Unscrew bolts that hold heating element in place. There will be wires that need to be carefully detached from the heads. Take heating element out. Install new one, reattaching wires and bolts in that order. It might be nice to clean the oven a bit while you're in there, as smelling something burning right after a repair job can be a bit unsettling! Ha. But it works great, and the fix is incredibly easy. So glad we didn't call a repairman.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- June from Merritt Island, FL
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I could not find a dealer who could tell me what part I needed because the model was discontinued
I just went to your web page and indicated I needed an 8' surface element and up popped a picture; I ordered it and plugged it in and it works perfectly. I didn't need a model number, or a part number. Three cheers for a simple solution and a 1st class web page!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jean from Broadview, NM
- Parts Used:
- WB44X10009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
old baking element burnt into
already had the old one disconnected (spade ends) on old element, new one arrived installed it the same way I removed the old part, just 2 little screws to hold it in place, after you reconnect the spade ends. Then plugged the unit back in. Always use common sense when working with electrical appliances! Easy as the pie I can now bake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Weston, NE
- Parts Used:
- WB44X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven heating element burned out.
Removed two screws, pulled old element forward 2 inches, removed two wires. Pulled old element out of oven. Put new element in oven, attached two wires, pushed element all the way in, put two screws in and tightened them. Turned oven on to test new element. Element worked. Project completed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chap from Edmond, AL
- Parts Used:
- WB44X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Old bake element caught fire.
It took longer to get the new element out of the box than it did to install it. I removed the two screws with a 1/4" nutdriver, pulled the element out roughly three inches, unplugged the connectors and discarded the old element. I did the reverse to install the new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from North Reading, MA
- Parts Used:
- WB44X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven heating element defective.
Removed old; inserted new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from seattle, WA
- Parts Used:
- WB44X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
oven bake element burned out
The repair went very smooth and easy it took me around 10 minutes to replace part and I was ready to bake again
Was this instruction helpful to you?
Thank you for voting!