JGBP28TED2WW General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dana from LEEDS, AL
- Parts Used:
- WB01K10112
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NEIL from ROCKY POINT, NY
- Parts Used:
- WB08T10026
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
BASE OF BULB BROKE OFF & WELDED TO SOCKET
PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marie from Woodstock, IL
- Parts Used:
- WB28K10025, WB28K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Front burners had to be lit with lighter
My son lifted up cooktop, unscrewed the front plate to gain access to old tube burners, removed and replaced with new parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- michael from The Villages, FL
- Parts Used:
- WB28K10025, WB28K10024
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
burners would not light
Remove the old tubes. Lift the lid NO MORE THAN FOUR INCHES. !!!!! Feel for the connections on the switch ends and attach losely. Carefully ( with some slight bending ) attach tubes to the burners. Tighten all connections. Do not over tighten.
The tubes broke originaly because , attempting to clean the area I lifted the lid too high.
The tubes broke originaly because , attempting to clean the area I lifted the lid too high.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICK from SAN JOSE, CA
- Parts Used:
- WB27K10141
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
failed oven controller
Removed screws to back plate, unplugged, removed controller and installed new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maureen from Locust Valley, NY
- Parts Used:
- WB15X10048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Oven handle broke off
Couple of screws and it was done. Simple and inexpensive since I thought I was going to have to buy a new range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Omaha, NE
- Parts Used:
- WB15X10048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Orignal oven door handle had multiple fractures and was fast becoming useless.
Removed the old handle with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Lincoln, CA
- Parts Used:
- WB07K10005
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
End cap cracked. Tried to fix it with epoxy, but it didn't work.
Used screwdriver w/star bit to remove two screws (longer one on top). Removed cracked end cap. Placed new end cap into position, making sure all tabs were correctly aligned. Replaced screws (top one first)tightening them slowly & alternating back & forth so as not to crack the new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Monterey, TN
- Parts Used:
- WB08T10026
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
broken light socket
The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Los Angeles, CA
- Parts Used:
- WB16K10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner would not ignite.
Could not have been simpler. Burner head dropped into place and was held in place by gravity. Not possible for part to go in incorrectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from Hauser, ID
- Parts Used:
- WB27K10141
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
clock quit. Teperature was off.
Pulled range out from the wall. Un-screwed 4 screws. Disconnect old control board. Plugged in new board. Easy, easy, easy! We used the old overlay. It peeled off easily. If you want a new one, be sure and order it as well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Brandenburg, KY
- Parts Used:
- WB08T10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Oven light wire broken, damaged socket
Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- AL from PHILADELPHIA, PA
- Parts Used:
- WB28K10025, WB28K10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
broken left /right range lines broke off
loosen the compression fitting both ends and screwed new ones in place .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Ann from Granby, CT
- Parts Used:
- WB02K10062
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic glide broke
The person I spoke to knew exactly what I was trying to describe. The part arrived in 2 days. 5 minutes later the drawer was back in place. I was glad I save the screw as the part did not come with one.
Was this instruction helpful to you?
Thank you for voting!