JGBP35SEJ2SS General Electric Range - Instructions

I turned the gas off and disconnected the stove & unplugged it from electricity. Pulled the stove out & removed the part. I ordered the regulator from PartSelect and it arrived promptly in 2 days. I replaced the Kit-Valve & Regulator with no problem. I changed the orfice jet from natural gas to butane. It works well.

replaced old with new.

Two set screws in rear; removed easily with a screwdriver. Old oven floor lifted out easily; new oven floor dropped in just as easily; set screws re-installed. Done. Pleasantly surprised at how easy this went.

Easy

Start by removing all screws 3 for each burner total of 15 t-15 bit is required then proceed to remove spark igniters 5 total slight pull next step would be to slide a screwdriver under top left and right side to remove top shelf. There you will have access to the parts you need to replace. When done just reverse installation instructions to complete

Removed burner and replaced

The person I spoke to knew exactly what I was trying to describe. The part arrived in 2 days. 5 minutes later the drawer was back in place. I was glad I save the screw as the part did not come with one.

called appliance repairman. He found problem and ordered new part. After 2 months waiting for part to get there, my husband got on internet and calld your number, and ordered what was needed. Now for the great thing. Within 4 working days we received what we thought we needed. but we had ordered the wrong part number. Got back on internet, went right to your web site, found the part that we did need, a flame spreader instead of the Deflector. called your service number, talked to a very nice person, again, told her what we did and ordered the correct part. Another great thing, we got that part the very next day. I returned the wrong part that same day. We then had our son install it and now we have a very nice working oven. Though out this very long ordeal, we talked to the applicance service people and got the same answer. The part has been ordered and it should be here next week. When we found your web site and called for the part, I called the appliance service and told them we had ordered the part ourselves and I would be happy to give her this information. THE VERY NEXT DAY she called us to tell us the part had fially arrived and they could come out the next day. Told them sorry but it as already taken care of. The very next time we need some part for any appliance we will call you first. Thank you for your very nice service people and the fast way that this all took place.

Husband actually did the repair, It went really well except he forgot to remove the heat shield from the old part to attach to the new bottom. (His mistake!)

I removed the bottom drawer, oven racks and bottom cover inside over, removed the screw at the front end of the burner. Unplugged the wire connector for the igniter. Removed the two retaining screws from the burner tube, removed from oven. Removed mounting screws from igniter to use on the new tube and igniter. Wire terminal did not match. Cut wire connector from old igniter, cut wire connector from new igniter. install old connector on new igniter with wire nuts.Install burner tube in oven. Connect igniter connector together. Reinstall over cover and racks. install bottom drawer. Turn on oven. Yah. It works. Their was a hold burned in the old burner tube causing the popping noise and finely not operating. Good to go. Bruce L Best Sr

Removed grill grates, gas distributors, etc. (just lift off). Used star screwdriver to remove screws (3 per burner for SML, 2 for power burner). Lift off stainless cover, which also lifts off the white sparkers I was replacing. Pull them off the wires (didn't need pliers, others said they did). Replace (make sure it is all the way on) and reverse your steps. White sparkers electrodes seemed loose when I put them back on, but tightened up when I fully secured the top back on. Make sure the wires aren't pinched underneath when you put the top back on. Recommended: If you've got one that isn't working, go ahead and replace all 3 (power burner is different) because the part is so cheap you may as well just do it now.

I removed two bolts at the rear of the oven bottom. I pulled the old oven bottom out, and put the new oven bottom in. I put the two bolts back in and voila it looks like a new oven. Done in less than 15 minutes.

Removed the old oven bottom by removing two nuts. Be careful...don't drop the nuts! Removed the heat shield that was attached with four nuts to the old bottom and transferred it to the new oven bottom. Then placed the new bottom in the oven and secured it with the two original nuts. Easy...but don't forget about transferring the heat shield and don't lose the nuts.

I opened oven and pushed oven rack inside.

Easily glide in.