EGR3000EL1BB General Electric Range - Instructions

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

Easy

remove old burner, put new in place

The part that was ordered based on the shamanic wasn't the part that was needed for the repair. It was to short. I took the other screw for the other side and that screw was an inch longer than the screw that was ordered thru your company. I then went too a jar that I placed extra screws, nuts and bolts which l keep in my garage . I found a same length screw but a different head and it works perfectly fine. When I ordered the part from your company most of the parts did not have a photo of the part on file, or a description like how long the part is. I still ordered it because it should fit the make and model number that was posted on the shamanic that was showed to me on line.

Removed the old caps and replaced with new burner caps. The stove top looks brand new. Thank you.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

First, I removed the two screws that hold the elements in place. I then pulled the element out about 3 inches and disconnected the door handle.
The bottom sleve holder that holds the glass part of the stove and I had to bend it back in place. Other than that, the repair went very well

Start by removing all screws 3 for each burner total of 15 t-15 bit is required then proceed to remove spark igniters 5 total slight pull next step would be to slide a screwdriver under top left and right side to remove top shelf. There you will have access to the parts you need to replace. When done just reverse installation instructions to complete

Removed burner and replaced

Removed grill grates, gas distributors, etc. (just lift off). Used star screwdriver to remove screws (3 per burner for SML, 2 for power burner). Lift off stainless cover, which also lifts off the white sparkers I was replacing. Pull them off the wires (didn't need pliers, others said they did). Replace (make sure it is all the way on) and reverse your steps. White sparkers electrodes seemed loose when I put them back on, but tightened up when I fully secured the top back on. Make sure the wires aren't pinched underneath when you put the top back on. Recommended: If you've got one that isn't working, go ahead and replace all 3 (power burner is different) because the part is so cheap you may as well just do it now.

I removed the bottom drawer, oven racks and bottom cover inside over, removed the screw at the front end of the burner. Unplugged the wire connector for the igniter. Removed the two retaining screws from the burner tube, removed from oven. Removed mounting screws from igniter to use on the new tube and igniter. Wire terminal did not match. Cut wire connector from old igniter, cut wire connector from new igniter. install old connector on new igniter with wire nuts.Install burner tube in oven. Connect igniter connector together. Reinstall over cover and racks. install bottom drawer. Turn on oven. Yah. It works. Their was a hold burned in the old burner tube causing the popping noise and finely not operating. Good to go. Bruce L Best Sr

The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.

called appliance repairman. He found problem and ordered new part. After 2 months waiting for part to get there, my husband got on internet and calld your number, and ordered what was needed. Now for the great thing. Within 4 working days we received what we thought we needed. but we had ordered the wrong part number. Got back on internet, went right to your web site, found the part that we did need, a flame spreader instead of the Deflector. called your service number, talked to a very nice person, again, told her what we did and ordered the correct part. Another great thing, we got that part the very next day. I returned the wrong part that same day. We then had our son install it and now we have a very nice working oven. Though out this very long ordeal, we talked to the applicance service people and got the same answer. The part has been ordered and it should be here next week. When we found your web site and called for the part, I called the appliance service and told them we had ordered the part ourselves and I would be happy to give her this information. THE VERY NEXT DAY she called us to tell us the part had fially arrived and they could come out the next day. Told them sorry but it as already taken care of. The very next time we need some part for any appliance we will call you first. Thank you for your very nice service people and the fast way that this all took place.

Replaced the burner and igniter after watching the repair video provided by Partselect. I was pleasantly surprised when the parts came the very next day. It was so easy and the igniter plug matched perfect. My wife wanted to hire a repair man but I did the repair and saved a bundle on the labor. I couldn't be happier about my purchase.

Remove bottom drawer,open oven door,take oven racks out,use flat tip screwdriver to remove two screws in back of oven. Then remove cover over burner and igniter.Reach under oven and unplug igniter,while down there use 1/4 inch nut driver and remove two screws holding burner. Then remove one screw inside oven in front of burner. Pull burner and igniter up and out of oven.I did not unplug stove or turn off gas some people may want to,if you have to move stove out to work on it