LEB316GT5WH General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Art from FRESNO, CA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
element broke
Fast shipping, Very easy to install I am a senior and had no problems works Great!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Corvallis, OR
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Replace bake heater element
Basically very easy. Be sure to follow suggested safe practices - DO shut off the circuit breaker to the unit BEFORE starting (I didn't to start with, shorted out the heater leads - dumb on my part). Just removed the burned out element by removing the 2 screws using a nutdriver, pulled the element out, and slipped off the crimp fittings. Reverse steps to install replacement. The crimp fittings were stubborn coming off the old one, so it took longer than expected. Otherwise, easy peasy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- allen from MT. AIRY, MD
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
bake element was broken
i slid the oven out unplugged it !! , removed back cover with a nut driver, removed the two retaining nuts from the old bake element ,opened oven door removed two nuts that hold bake element to the back of the oven , installed new bake element then attached wires in the back of oven to the new element re installed retaining screws inside oven , check to make sure screws that hold power cord wires to the over are TIGHT !! i then installed rear cover then plugged in the oven it worked great !!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Derrick from Ypsilanti, MI
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Oven no longer heated except for Broil element
1)Unscrewed old baking element from wall of oven
2)Detached old baking element from wires
3)Attached new baking element to wires
4)Screwed new baking element to wall of oven
5)Turned on oven
2)Detached old baking element from wires
3)Attached new baking element to wires
4)Screwed new baking element to wall of oven
5)Turned on oven
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard L. from Clear Spring, MD
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
No heat lower bake unit / Broiler unit heats ok
Safety first: Turn range circuit breaker to off position. Turn a surface unit [burner] to the on position ,if no light exists power has been removed. Turn surface unit to off position. To remove bake unit. With a 1/4 socket driver remove two self tapping screws and gently pull out on the bake unit until you can access the slide on terninals. Careful lenth of wire is limited. Remove slide on terminals two each [2] . Install new bake unit in reverse order . Restore power
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from MARTIN, GA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
bake element was fried
I went by the video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from BLUFFTON, SC
- Parts Used:
- WB30M1
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken heating element
remove broken heating element and install the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from PROVO, UT
- Parts Used:
- WB31T10011, WB31T10010
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old drip bowls were badly tarnished . . . shine could not be restored.
1) Make sure unit switches are turned off. 2) Lift Calrod unit up and pull it from electrical receptacle. 3) Withdraw Calrod unit from old bowl. 4) Insert Calrod unit through large hole in new bowl. 5) Push Calrod electrical connectors into receptacle under range top. 6) Seat Calrod unit on bowl rim and insert the assembled Calrod unit and bowl into the hole in the range top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Franz from CRESTVIEW, FL
- Parts Used:
- WB44K5012
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven would not heat
Removed old broken element and installed new one. Took less than 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Rowlett, TX
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner worked intermittently
Lined up the prongs and slid it right in, took 30 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Iron River, MI
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
burnt element
.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from Covington, LA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Old element burned in half
I turned off the power going to the stove, unscrewed the 2 screws, plugged in the 2 inserts, put the 2 screws back and PRESTO!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Martin, TN
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Bake Element went out..flamed out pretty big light show when it happened
The job went over without a hitch, only probably didn't get the correct part first go around, but after getting the right part everything went very easy..Just a couple of screws where the elment goes in and 2 wires to plug back into the new element, after that everything was good to go!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Muncie, IN
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Tenant broke bake element
Removed the two screws, pulled out old element, installed new element, and reinstalled screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from NEW BERLIN, NY
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
element broke
took 2 screws out that held element in, pulled old element out of oven wall, unhooked the wires. Hooked the wires to the new element, pushed it back into the oven wall, replaced the 2 screws.
Was this instruction helpful to you?
Thank you for voting!