Models > JBS23BB1 > Instructions

JBS23BB1 General Electric Range - Instructions

Jump to:

All Instructions for the JBS23BB1
61 - 75 of 208
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Thomas from Tunbridge, VT
Parts Used:
WB44X10009
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers
Oven wouldn't heat
First I unpluged the appliance. Then I removed the cover from the back of the range. I then disconnected the two wires from the element. I then removed the two screws that hold the element in place. I then removed the old element and reversed the process to install the new one.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Susan from Bend, OR
Parts Used:
WB21X36771
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
The small element blew out consequently shorting out the infinite switch.
The very first thing we did was turned the circuit breaker off and unplugged the range.
My husband removed the back panel and unplugged the switch. Drew a diaghram of the color coded wires. When we received the new one he broke the extension bar off to fit the knob, plugged it in and we were back in business. It was very easy for my husband as he is a mechanic (millwright). However, if you are mechanically inclined it is an easy fix.
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from West Liberty, KY
Parts Used:
WB21X36771
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
Knob/switch would not turn right front burner on at all!
Pulled range out from the wall. Unplugged cord from outlet. Removed old knob, removed two phillips screws a very top of chrome trim, removed six nut-head screws from back to reveal the switches...removed two set screws from the front at knob base. Visually checked to make sure wiring post of new switch matched the old one. There was enough slack in the wiring to remove one wire at a time and connect it to the new switch in its appropriate place. Put new switch in the panel and secured with the two set screws. Select the bushing that would take up the slack for the old knob to fit on the new switch stem. Held new stem at its base with pliers and used another pair of pliers to snap the stem at appropriate length. (The new stem could not be broken off short enough to have the knob as flush to the panel as the other knobs...this was the only negative factor in the repair) Replaced nut-head screws and phillips screws. I was especially pleased with the quick delivery of the part...even without special shipping rates I received the part in less than 18 hours from the time I ordered it online!
3 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from Billerica, MA
Parts Used:
WB44X10009
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Oven wouldn't bake - visible damage to heating element
Unplugged oven. Pulled out from wall and removed backside access panel. Unplugged 2 stake-on connectors connected to element. From front side of oven, removed fan guard using 1/4 inch nutdriver. Gained access to and removed two screws holding in element. Pulled element out. For installation, reverse process.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Nancy from Westport, NY
Parts Used:
WB44X10009
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers
Bake element arched and burned
First, we ordered the part on Sunday afternoon online. It was here by Tuesday morning. We unplugged the oven and removed the screws holding the element in place and the electrical contacts. That was the toughest part because it's hard to get in the oven and they were baked on pretty well. We had to drill holes in the bake element. Be careful not to drill them too big, so the screw will fit snug and make contact. We screwed the bake element to the contacts, then back to the over, plugged it in and turned it on. The temperature is more constant and steady than ever, and the oven heats much faster. We were impressed and happy to avoid replacing the whole stove.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
thomas from HENDERSONVLLE, NC
Parts Used:
WB44X10009
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
bake element broke into two pieces
unpluged unit then removed back panel unpluged element then took the two screws out took old element out replaced with new one put screws back plug element back in put back panel on pluged it in and started baking home made chocolate chip cookies
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Carolyn from Garden City, ID
Parts Used:
WB31T10011, WB31T10010
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Needed New Burner Bowls
Removed the old burner bowls, replacing them with the new ones.
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
charles from st marys, GA
Parts Used:
WB31T10011, WB31T10010
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
part replacement
pull out, push in
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Caren from Choctaw, OK
Parts Used:
WB31T10011, WB31T10010
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
rusted drip bowls
I was very excited to get them in the mail but waited to install after a clean up but when I finally opened the box I found I only ordered 1 6 inch drip bowl. lol Now that I know they fit when I reorder I am ordering a who new set for later use.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Gary from Delevan, NY
Parts Used:
WB44X10009
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
Burned out Bake Element, oven would not heat.
Of course the first thing is to turn off the breaker, Unplug the appliance, pull the two electric feed wires off the old element. Then remove the four screws that hold the fan guard in, After that the two screws that held the Bake Element in place. Then reverse the process to install the New Element. Took about twenty mins. from start to finish. Just Like New. And thanks to Parts Select for their prompt service, Had the new part in two business days.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Woolwich Twp., NJ
Parts Used:
WB21X36771
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
no power going to burner when switch is on, switch bad
I followed the easy instructions and everything went well. I had the new switch installed in about 30 minutes. My wires were different colors than on the instructions but it was still easy to figure out where the wires went on the new switch. Just do not be in a hurry and make sure you measure before you break off the extension bar. My knob fit on the new switch without any of the parts that came with the switch.
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
joseph from san jose, CA
Parts Used:
WB36X192
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
dropped & broke the oven light bulb cover
popped the new one on!
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Stuart from UNION SPRINGS, NY
Parts Used:
WB31T10011
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Drip bowls had deteriorated after years of use
Removed burners and existing drip bowls and installed new drip bowls and existing burners took approximately 15 minutes
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Tim from Beltsville, MD
Parts Used:
WB44X10009
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Bake element was broken
It was so simple looking, I had it shipped to the tenants of the house. They swapped it out easily, and were happy to get back to baking.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Natalie from Harleysville, PA
Parts Used:
WB30M2
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Surface Element/burner had to be replaced
First, I removed the burner from the box and plastic bag. Second, I pushed the burner into the socket and that was it.
I also want to comment on how easy the ordering process was. I ljust love this website. All you have to do is type in the model number and up comes all of the parts associated with the appliance. My order shipped the next day and I had unit within 2 days. Also, the part cost $42.00 with shipping. My local parts place was $48.00, so I wound up saving $6.00 and did not have to leave my home to buy it. I will definetly use this site again.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JBS23BB1
61 - 75 of 208