JBS02*R1 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kenny from CALDWELL, ID
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Bake element did not work
Got new part! Unplug range!!!
Remove oven door by opening and lifting up at the same time, set aside.
Remove two screws with a nutdriver or screwdriver.
Pull on element far enough to unhook wires and throw away old element and install the wires on the new element and reinstall!!
Remove oven door by opening and lifting up at the same time, set aside.
Remove two screws with a nutdriver or screwdriver.
Pull on element far enough to unhook wires and throw away old element and install the wires on the new element and reinstall!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Buffalo, NY
- Parts Used:
- WB31K10266
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace a drip pan
OK, I put the drip pan under the burner. Without a single problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES from SAN JOSE, CA
- Parts Used:
- WB17X5113
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
terminal block not working
simple remove the old one, strip old wires to make longer, twist wires together, put on wire nuts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from MANHATTAN, KS
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Bake element began to spark and short out when I tried to use it.
When the part arrived, I used the diagram provided by the website to see what really needed to be done. Keep in mind, if you're doing it correctly and disconnect the range from the power source, it's going to be dark inside the oven. Get a good flashlight or electric lantern. There are two screws holding the element in. Mine were 8MM hex-head screws, but be prepared for anything. I removed the with a socket attachment/adapter to my cordless drill/screwdriver, and the part came right out. Some insulation will come as well - don't panic. Installation is similar, just in reverse order. Pay attention to the feet on the element. Make certain they are down. Don't lean on them when you think you're finished and discover that you installed it upside down like someone I know, and have to pull it out to correct this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Catherine from silver spring, MD
- Parts Used:
- WB17X5113
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
needed to replace a receptacle
I had already removed the worn out part. The new part came with wire joint covers and connecting them was fine. The brace that came with the part did not actually fit onto the stove burner well; so I cleaned and used the older brace - but, when I went to put it back in place, the bearings on the original self locking bolt were stripped. So, I had to find a replacement bolt with a nut. Found that I had some of those on hand. Once the brace was firmly in place, the rest was easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Hindman, KY
- Parts Used:
- WB21X36771
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Burner wouldn't operate
Took Switch panel off range. Disconnected Infinite switch. Reinstalled infinite switch.. Replaced panel. Repair was very simple and self explainatory.
Knott County Housing Authority Maintenance Personnel
Knott County Housing Authority Maintenance Personnel
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Thornton, CO
- Parts Used:
- WB48X5099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bottom oven rack had been NUKED!
This is far to simple to even be a worthy story ,other than that the cause is a bit interesting. My wife had placed a plastic cutting board and some meat into the oven to get it away from my counter-cruising dog.
Later, without remembering the cutting board she turned the oven on to "broil." Hmmmm...
REPAIR:
Open oven door
Put in new rack
Close door
Later, without remembering the cutting board she turned the oven on to "broil." Hmmmm...
REPAIR:
Open oven door
Put in new rack
Close door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joel from Avon, OH
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Up to 1 hour for oven to preheat
Removed 2 nuts holding the baking unit to the oven back, removed 2 nuts holding wires in place, installed new unit following procedure backwards. It takes longer to get the tools,take the oven door off, and take racks out than it does to remove and replace the baking unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Richmond, VA
- Parts Used:
- WB31K10265, WB31K10266
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed new burner bowls
No repairs, really-just replacement, but I have been looking for the burners for three and one half years, and PartSelect had exactly what I needed for this old stove!
Theyalso had the electric element that I bought in the next order.
Theyalso had the electric element that I bought in the next order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Hanover, MA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Oven Heating element broken
Turned off power to the oven at the circuit breaker. Pulled the old heating element from the back lower wall of the oven. Noted the position of the wires (right terminal attached to the red wire, left to the black wire). Removed small bolts holding the element to the wires using pliers. Attached the new element using screw driver. New element came with screws, not bolts. Pushed the element back into place and restored power. Tested to make sure everything worked. Everything works and I ran an oven cleaning cycle. Noticed that indicator light above the temperature selctor is always on now even when oven is in the OFF position. Not sure if that's related to the change or to the oven cleaning cycle I ran. In any case, oven seems to work normally.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Westport, IN
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
element burned out
Took off the door, took out the two screws in the back of the element. Then pulled the element forward, then removed the two wires. Then put it all back together with the new element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynn from Dallas, TX
- Parts Used:
- WB17X5113
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The heating coil on the stove blew, or wouldn't work.
I simply replaced the female part of the plug that the coil plugs in to. I figured this would do the job. I replaced the part,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandy from Olney, MD
- Parts Used:
- WB31K10266, WB31K10265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The original drip pans had rusted and needed replacement.
We tried to find the replacement pans at the local hardware store and were disappointed in that although they were cheaper, they were not deep enough to handle the heating elements. We were delighted to find that the parts from PartSelect.Com were genuine GE parts... installed in minutes and were delivered VERY quickly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Suzanne from Brigthon, MI
- Parts Used:
- WB31K10266, WB31K10265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the drip bowls were a mess- rusty and beyond cleaning
I removed the old drip pans, cleaned the range top, washed and installed the new drip pans and put the old pans, box and packing materials in the trash. In only 12 minutes my range top looked like new and the mess was picked up. Now, if I could just get the rest of the kitchen looking that good that fast!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carolyn from Harvard, MA
- Parts Used:
- WB44X5082
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven wouldn't heat because coil had burned through
The part was delivered in 24 hours with regular
shipping and was simple to replace. Uncrewed
it, disconnected wires from the old one and connected
the new one. Cost a little more than $30 including shipping and the oven works great!
shipping and was simple to replace. Uncrewed
it, disconnected wires from the old one and connected
the new one. Cost a little more than $30 including shipping and the oven works great!
Was this instruction helpful to you?
Thank you for voting!