JGHC60GEJ2 General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Boston, MA
- Parts Used:
- WB3X712
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob was broken
Changed the knob. Just like that, it worked like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Clay, NY
- Parts Used:
- WB24X379
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Right front burrner wouldn't start
Pulled the knob's off the front of the stove. Removed 7 phillps screws holding on the front plate, pulled off the front plate, removed the ignitenr, and then reassembed the stove. It worked great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- charles from brick, NJ
- Parts Used:
- WB3X712
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old knob broke
it was tooooo easy. Just pushed the new one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christine from new york, NY
- Parts Used:
- WB2X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would not light
Removed old ignighter and replaced it with the new one. No brainier. Took longer to find the correct part, mine had three wires, most are just two.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Winter, WI
- Parts Used:
- WB28X67
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Only one and a half burners worked.
I just had to lift the top of the stove. Then pull the old burners out and put the new ones. It took longer to ignite the flame than replace the burner. Works great !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aurora L from Sacramento, CA
- Parts Used:
- WB3X712
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The knob that turns on the gas fire broke so I ordered a new one.
I really didn't have a clue as to where to get one so I just went without a knob not using the burner for about a year. Then I decided to call a handyman. He said the part would cost $20 and labor would be $50. I said forget it. I immediately got on my iPad and researched. I found the exact part! It came in less than 30 hours of ordering it. Then I opened the plastic bag with the knob in it, and it fit exactly right into place. And Voila! I could finally use that burner again. It was so easy to Install, no,tools necessary. It fit right into place ! I should have done that earlier had I known it would be so easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeremy from Williamsburg, VA
- Parts Used:
- WB3X712
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replacing Broken Knobs
Just put the new knobs on and they worked good as new.
Was this instruction helpful to you?
Thank you for voting!