JGB915BEF2BB General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ERNEST from MANCHESTER, NJ
- Parts Used:
- WB35X37973
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
finish on old oven bottom was damaged
Ordered part from customer friendly Part Select and received the replacement part within a few days, and installed it promptly. Wife is happy and stopped grumbling about oven bottom unsightly defect! Small price to pay for a happy wife! Ernie
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NEIL from ROCKY POINT, NY
- Parts Used:
- WB08T10026
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
BASE OF BULB BROKE OFF & WELDED TO SOCKET
PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from SOUTHBURY, CT
- Parts Used:
- WB20T10024
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Temp probe was defective
Threw the old one out - plugged the new one in. Steak came out just as ordered - medium rare.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hughie from Mansfield, LA
- Parts Used:
- WB19K10041
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Strong odor of butane- gas leak at regulator
I turned the gas off and disconnected the stove & unplugged it from electricity. Pulled the stove out & removed the part. I ordered the regulator from PartSelect and it arrived promptly in 2 days. I replaced the Kit-Valve & Regulator with no problem. I changed the orfice jet from natural gas to butane. It works well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Herndon, VA
- Parts Used:
- WB02K10011, WB02K10136
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Self Cleaning Safety Latch broken
This was a difficult repair because half of the screw on the stove top had to be drilled in order to get access to the device that operates the locking mechanism for the door latch for the self cleaning oven function. Once all the screws where removed it was an easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from LEEDS, AL
- Parts Used:
- WB01K10112
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Tucson, AZ
- Parts Used:
- WB20T10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Probe Sensor
Replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Columbia, TN
- Parts Used:
- WB16K10035
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Burner had a hole burnt in it, glow plug broken
Removed burner and replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce Lee from Carson City, NV
- Parts Used:
- WB16K10035
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
No heat from Oven Burner. Alos poping explosion noise when burner ignited
I removed the bottom drawer, oven racks and bottom cover inside over, removed the screw at the front end of the burner. Unplugged the wire connector for the igniter. Removed the two retaining screws from the burner tube, removed from oven. Removed mounting screws from igniter to use on the new tube and igniter. Wire terminal did not match. Cut wire connector from old igniter, cut wire connector from new igniter. install old connector on new igniter with wire nuts.Install burner tube in oven. Connect igniter connector together. Reinstall over cover and racks. install bottom drawer. Turn on oven. Yah. It works. Their was a hold burned in the old burner tube causing the popping noise and finely not operating. Good to go. Bruce L Best Sr
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Albuquerque, NM
- Parts Used:
- WB02T10017
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Convection fan came loose from shaft
Convection fan came loose from the shaft with a lout rattle and grinding as the fan spun down. Had to remove four metal screws to remove the fan cover. Initially tried to just put the nut back on to hold the fan. However, I could not get the nut to start, so I assumed that threads were stripped on the nut or the shaft. Ordered the replacement nut, hoping that it was the nut that was the problem. However, I had the same problem with the new nut. I could see no damage on the shaft. It finally occurred to me that the nut and shaft had left-hand threads (counter-clockwise to tighten). At that point, it was extremely easy to put the nut back on and tighten it. I did not try using the old nut, since I had already received the new one, but I'm certain that if I had come to that realization earlier, I could have saved time and money. So, if you have the same problem, try putting the nut on "backwards."
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from Watervliet, NY
- Parts Used:
- WB35X37973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Forgot to remove the heat shield from the old part.
Husband actually did the repair, It went really well except he forgot to remove the heat shield from the old part to attach to the new bottom. (His mistake!)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Monterey, TN
- Parts Used:
- WB08T10026
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
broken light socket
The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.
Was this instruction helpful to you?
Thank you for voting!