JBC27BY3 General Electric Range - Instructions

I pulled the old burner out and slid the new one in it's place. Turned on the eye to make sure it worked. Felt heat in a few seconds and turned off.

First, used the nutdriver to remove the two screws that hold the element. Then pulled out the element 4 inches. Disconnected the two wires from the old element and discarded it. Connected the wires to the new element and tightened them a bit by squeezing with pliers (not too tight, but just enough so they won't disconnect easily). Pushed the wires back through the insulation and screwed the two nuts back in place, making adjustments so that the element is level.

I had a great experience with part select. The part was easy to find and arrive within two days in perfect conditions. Everything went smoothly with the repair and the element is working very well.

Removed both racks, removed two screws holding element in. Removed two screws holding wires on element. Drilled holes in new element where the push-on connectors are attached so I could attach the oven wires to the new element. Attached the wires and screwed the element to the oven. Fit perfectly and the temperature of the oven matches the control knob finally!

Thanks.

They fit perfect

Disconnect power to range, remove fan cover (4 screws).
Remove old element (2 screws).
Pull off wires from old element.
Discard old element, clean bottom of oven.
Slip wires on terminals of new element.
Install new element,and fan cover.
Reconnect power.

ordered parts and disassembled old burners and installed new ones. All the parts were in the box when delivered.
Helping my 80 yr old mother-in-law very happy.

Got parts in for one of her 81st birthday present she was thrilled.

Used a nut driver and removed to studs and pulled the old element out and disconnected the two wires. Then connected the new element and put the studs back. It was that easy. Great website and it only took 5 minutes to order the part and received it on time. Plus my wife was trying to cook thanksgiving dinner. Thanks

I've been looking for an 8" replacement burner for my GE stove after my original burner caught on fire over a year ago. I had all but given up on finding a replacement after searching at all the stores in my area and also searching on the net. After cooking sides for Thanksgiving dinner this year and the pain of cooking with only 1 large burner, I decided to search again for a burner on line and thank goodness I found this site! All I did was put in the model number of my range/stove and the site directed me to the replacement burner. The picture of the burner looked like mine, so I decided to purchase it but I still wasn't convinced it would fit and work because of my failed previous burner purchases. I really thought my burner was too old and the part was no longer made. Well the part shipped very quickly and lo and behold it fit and worked! Installing was a breeze...I just snapped it in...thanks so much!

I ordered it on line and it was easy to fix, I had it done before my husband came home from work. I just undid the old one and pushed the new one on. I have to stay ordering from here was alot cheapier

I simply pushed the new burner into hardware. I then tested it to see if it works. . .

Just put it right into the receptacle. I want to add...we had gone to our local appliance store and brought home a wrong-size unit. Got online and your website came up. It was easy to find the correct part, ordered it and it arrived 3 days later. I have already recommended your website to 2 of my friends. One very good experience!!!

My Husband did the repair. It took him longer to prepare the appliance than it did to perform the actual replacement of the bake element! We LOVE the service and the selection found at PartSelect!! Our part arrived within 24 hours!We've recommended you to all our friends and co-workers. Bravo! Thank you again.

Removed the cover plate, pulled the element out, removed the screws holding the wires in place, but then I had to enlarge the screw holes on the new element in order to fit the screws into the new element. Took a while with an awl to enlarge ther two holes. Connected the new element, pushed it back in and replaced the cover plate. Worked great.

1. The infinite switch had several knobs which would fit the switch shaft. Read the directions included with the switch in order to have the shaft fit the proper knob. You can break the shaft with two pairs of pliers. 2. Move the stove away from the wall and unplug it. 3. Remove the 1/4 screws from the back side of the stove and remove the back panel, exposing the switch. 4. Remove the wires one at a time and put them on the new switch. The terminals are L1, L2, P, H1 & H2. The Pilot (p) has a smaller terminal so you don't get it mixed up. Generally L1 is black, L1 is red, P is yellow, H1 and H2 can be blue, brown, yellow, orange or one of these colors striped on a white wire. 5. Remove the old switch from the stove and be sure to save the two mounting screws. 6. Position the new switch so that the side of the switch marked "top" is on top. 7. Install the screws on the new switch and put the knob on it. 8. Carefully test the burner. 9. Unplug the stove and put the back cover on.

Remove the front panel, at which time the spring loaded door slammed closed while the paned and handle were in my hand. Fortunately I had a star bit to fit the screw holding the door and panel together.The parts should come with 2 screws since the part has holes for 2. note: the factory installed handle only had 1 screw in each side.