JB600CD1CC General Electric Range - Instructions

Performed repair using a video for reference.

First I removed the two screws that hold the element in place. I then went to pull the element out and one of the wires touched the side of the access hole. There was a spark and the electrical breaker tripped. (Remember to always shut the electricity off first). Before I put the new element in I took off the access panel on the back of the range, slid in the new element, attached the two screwd that hold the element in place. Then I went around to the back of the range and re-connected the wires from that location to make sure there was nothing around the wires that would spark. Put the access plate back on and I was done.

My exact model number did not appear in the listings, nor were the oven rack measurements clearly stated in items offered. I sent an email to customer service, received an immediate response with the correct answer (re: which part would fit my oven), ordered this item, and had a shipment arrival within days. The racks are a perfect fit, and they look great. The price is less than any other site I investigated.

My husband actually did the replacement but I did all the research online to find the right part. I wasn't sure we'd find it for our old stove but luckily we did and it works fine. Thanks for the super fast service!

I first pulled the stove away from the wall to unplug and look from the rear. Look at the wiring from the back (you may have to remove 2 screws and the plate that covers the wiring) and take a picture of it if you can with your smart phone - this way when you go to put it back you have a reference. I then removed the oven racks and the 2 little bolts holding the element in place. Wiggle it toward you slowly so the wires don't pull off. It's easier if you use needle nose pliers to get the fittings off, if its hard wiggle the fitting it will come off. I put the connections on the new element and squeezed them tight not to move. I did put a small piece of electrical tape on the connection ends for my piece of mind. Screw it back in and, plug it in and turn on. If the element starts to glow your done, put the cover back on over the wires and slide it back in place. If your kind of handy you can do it.

Watched youtube video. Very easy to replace

Unplug stove.
Remove rear panel of stove with a nut driver or socket. Remove knob from switch and use small screwdriver to remove screws on front panel switch. Remove and replace each wire contact one at a time to ensure correct wiring configuration. Replace screws on front panel to secure switch. Plug stove in and check that it works properly. Replace rear panel and move stove back in place.

Robert did not do the repairs. I did! 70 year old housewife. I watched a Utube video and thought I could certainly handle that. Ordered my part from your site. It came in two days. Burnet was replaced in under 20 minutes by me! Anyone can do this. Super easy, parts just plug in.

Pulled stove out and unplugged. At the rear of the range there were 4 faster. Used a nutdriver piece in an electric drill. Pulled off the cover and located the switch. At the front of the stove, I removed the knob and unscrewed two screws releasing the switch. I undid and replaced each wire connector one-by-one to avoid any wrong connections. Replaced and secured the switch and replace the back panel. All secured, power on and fixed! Easy repair, but something that had been put off for a year!
Also follow the installation videos from PartSelect - very helpful!

Took out the 2 screws,Pulled out the stove
Took the back off ,took the wires out of the little place where they fit in,Removed the old element.
Put the new one in Fitted the little thing which looked like a alumium flat piece back where we took the old one out.Put the back back on cut it on wheepe In business.Also the new element came here faster than I thought it would .I,m a 71 yearold grandmother.Pretty simple.

1st and formost, unplug the range from the outlet or shut th breaker off (Ranges are on a seperate breaker). Detach 2 wires on the back of the range connected to the element. Remove three nut screws inside the oven holding the old element in place . 1 on the top and 2 at the back of the oven. Now just reverse this procedure to install the new element and your all done.

Fue muy facil desconectar primero la estufa despues quite los tornillos de la parte superior detras de la estufa, desconecte un cable del switch y lo conecte en el nuevo despues el siguiente hasta conectar todos los cables en el nuevo switch. Lo mejor es desconectar uno por uno para mo mesclar los cables , despues removi el switch de la estufa y puse el nuevo , puse las partes de regreso y listo conecte la estufa t revise si funcionava el quemador y listo sin ningun problema.

It took a bit of head scratching to remove the oven door. I had read another user saying he'd removed the hinge screws unneccessarily, so I left them alone. I eventually was able to locate the locks on each hinge. Once they were disengaged, it was a simple matter to lift off the door. After that, I removed all the screws (except the hinge screws) and took the door apart. Once it was disassembled, I found two loose triangular pieces, about 1 1/2" long. I later discovered these were spacers for the two top srews. They were placed on end, and the top screws passed through them. All in all, a relatively simple repair, which absolutely amazed my wife, landlord, faily, etc.

Placing the order was very easy. Shipping was fast and excellent packaging. Thank you very much!

Nothing really rocket science here. The oven racks had burned on food, and I just replaced the racks..... slide out the old and slide in the new. Done !