JGBS23SEL3SS General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Leo from Roseville, MI
- Parts Used:
- WB28K10190, WB28K10189
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
open cook top / tubs pulled out front of stove
unplug power and turn off gas/// had to remove all star screws on top/remove ign wire from each burnner/now remove stove top/ adj wrench and remove nuts from the front nobs and relace with new front orifice tubes NOTE: Front orifice tube is the leftside. Front orifice HOLDER is the right side. put back top, open front to put hand in to make adjustments to ign wires close top and reinstall star screws and using finger to hold and make adjustments on top now turn power and gas on. I use soapwater to test for leaks/ leo gubin
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rose from Edinburg, IL
- Parts Used:
- WB16K10043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
hole burned in oven burner tube. making noise
changed old burner tube , with new equipment. thanks to PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Jessup, PA
- Parts Used:
- WB28K10190, WB28K10189
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Bent/Broken Front Orifice Tubes
I removed the two nuts that secure the rear orifice tubes. This allowed me to lift the range top to access the broken tubes. Once lifted I removed the nuts that held the broken orifice tubes. I then connected the new orifice tubes. I removed the three(star)screws that fasten the orifice brackets under the range top. Doing this allowed me to connect the new tubes without having to maneuver them at all. I then lowered the top just enough to reattach the brackets. After securing the rear tubes I snapped the range top back into place. Just remember, if you use propane for cooking then you must remove the brass orifices from the old tubes and place them in the new ones. If you don't do this then your flame will not burn properly. Simply unscrew them from the old tubing and put them in the new tubing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Burlington, OK
- Parts Used:
- WB20K8
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven Would Not Turn Off
Opened up the top of the stove using a screwdriver. Lifted it up about 3 inches and legs popped out on each corner and held it in that position. Traced the wire to the back and down to the oven. Pulled new thermostat along that route. When I got to the back it was a little tricky moving the thicker end around and down into the hole without removing anything from the back- but I did manage to do it. I then unhooked old thermostat from 2 clips, inserted new one and then went to the front and unsrewed the 2 small screws behind the oven control knob. Magnetic bit on screwdriver is a must! Pulled it back and removed wires one at atime and put onto new unit, then screwed it back in place and replaced knob. Plugged it in and turned it on. It came on ,stayed lit. Turned it off and it stayed lit- surprised me. . . . . . 25 Seconds or so and it went out. . . . . Job done!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from Watervliet, NY
- Parts Used:
- WB35X37973
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Forgot to remove the heat shield from the old part.
Husband actually did the repair, It went really well except he forgot to remove the heat shield from the old part to attach to the new bottom. (His mistake!)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TRICIA from INGLESIDE, IL
- Parts Used:
- WB16K10043
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Igniter was getting red hot but was not starting burner!
Very easy repair! Removed lower oven pan/ plate. Removed burner tube with 3 screws, removed igniter and reversed to reinstall!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Geneseo, NY
- Parts Used:
- WB20K8
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven would not turn off even though knob was turned off.
Unplugged stove. Removed the top rear panel to see where the thermostat cable fed into the oven. Left the current cable in place and fed new cable along side the old one. Pulled out the old cable once new one was installed. Attached wires to new thermostat and installed. Turned oven on to test. Everything went great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from harrisburg, PA
- Parts Used:
- WB20K8
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Would Not Turn Off
I read the instructions from other peoples repairs. One note: unplug stove, and turn gas off, remember where wires go. I didnt have to remove top of stove completly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vicki from Irvine, CA
- Parts Used:
- WB48T10095
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced damaged oven rack
I ordered the oven rack on a Tuesday and received it the very next day - was wowed at the service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Vicente from Joliet, IL
- Parts Used:
- WB34K10010, WB34K10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Medal Burners
I have had my medal burners for 5 years and with young adults cooking I could not seem to get them cleaned. They had the part that I needed and now I have a whole new top stove. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Los Angeles, CA
- Parts Used:
- WB16K10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner would not ignite.
Could not have been simpler. Burner head dropped into place and was held in place by gravity. Not possible for part to go in incorrectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joan from Brooksville, FL
- Parts Used:
- WB34K10010, WB34K10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Pans were old and looked it!
The repair was just to exchange however, I am still shocked with the delivery. I ordered one day and they were delivered one day later. I was amazed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- glen from felch, MI
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
uneven flame and sputtered, burner was not useable
Simple to correct 1. lift off grate 2. lift off burner cover 3. lift off old burner. 4. replace burner, cover and grate. took 10 seconds. burner works perfect
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robbin from Somerville, NJ
- Parts Used:
- WB34K10010, WB34K10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed new burners, gas tops and grills for hotpoint range
Customer service was above excellent! Parts delivered quickly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebecca from Las Vegas, NV
- Parts Used:
- WB27T10469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
no display
Turned off circuit breaker to stove, remove top panel and then the old control module and installed replacement. Power back on and top panel reinstalled. Easy!!! And Everything works like new!!!
Was this instruction helpful to you?
Thank you for voting!