JBS07V6 General Electric Range - Instructions

First I shut off the power at the power box. Second I removed two screws in metal plate. Third I unplugged the two wires. Repeated steps backwards and it works great.

saw when heating the stove up the bottom element wasn't getting hot. got part number and looked up online and ordered

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Just removed the elements and inserted the new drip pans. Could not have been easier.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and unscrewed the the two screws that connected the wires and element together. I then tried to connect the new element to the wires, but found that the screw holes were smaller than the original holes in the old element and the original screws wouldn't fit. No problem, I then got a cordless drill and found a drill bit a little bigger than the holes, I held the element connector with pliers and made the screw hole a little bigger, same with the other connector. I screwed the screws into the connectors with a socket wrench and then screwed the element back into the holes in the oven, then turned on the oven and it works as good as new.

I located and removed 2 sets of hex-head screws under the front lip of the cooktop, then lifted the entire cooktop to access the burner controls. Removed the wires and taped them, and took out the old control after removing 2 phillips head screws. Installed replacement part easily. Only tricky part is that the various shaft adapters don't quite work with my knob. I'll fix it completely with a bit of epoxy and the adapters they sent.

disconnected electricity, used pinch pliers to remove broken ends from connection box and used an already existing element to make sure a new one would work at all. Ordered new one that arrived very quickly and replaced the broken one. After years of taking these in and out for cleaning by outside cleaning help they are bound to break off. I will do the gentle removal from now on.

Removed oven door and racks. removed fan cover to expose elements two retaining screws.removed retaining screws and pulled burned element forward to expose electrical connectors.unconnected slide on connectors from old element and pushed leads onto new element and re-assembled.

First, used the nutdriver to remove the two screws that hold the element. Then pulled out the element 4 inches. Disconnected the two wires from the old element and discarded it. Connected the wires to the new element and tightened them a bit by squeezing with pliers (not too tight, but just enough so they won't disconnect easily). Pushed the wires back through the insulation and screwed the two nuts back in place, making adjustments so that the element is level.

I had a great experience with part select. The part was easy to find and arrive within two days in perfect conditions. Everything went smoothly with the repair and the element is working very well.

Removed both racks, removed two screws holding element in. Removed two screws holding wires on element. Drilled holes in new element where the push-on connectors are attached so I could attach the oven wires to the new element. Attached the wires and screwed the element to the oven. Fit perfectly and the temperature of the oven matches the control knob finally!

Thanks.

They fit perfect

shut off power, removed self tapping nuts, removed element, put new element in, re-attached nuts.

Removed the old and slipped in the new.No problem and it works fine.

Installation took 30 seconds. Your website was easy to use & the part received was just as described. It arrived beautifully wrapped & in just a few days. ABSOLUTELY AWESOME!I will recommend your site to everyone.

I pulled out the heating coil and pushed in the new coil. I turned the stove top on and heard a sound like "dzzzt". I immediately turned off the burner and waited for it to cool, then pulled it out. The part had a burn melt on one side of the end prong. It turns out that the part that the burner plugs into needs to be replaced. Actually, the stove top is over 20 years old and my landlord will have to replace the whole unit. So it turns out that I didn't need to order a surface element after all, but it was very easy to install!