Models > JGBS23SEH5SS > Instructions

JGBS23SEH5SS General Electric Range - Instructions

Jump to:

All Instructions for the JGBS23SEH5SS

Customer:: Gary from Alameda, CA
Parts Used:: WB20K8
Difficulty Level:: A Bit Difficult
Total Repair Time:: 30 - 60 mins
Tools:: Nutdriver, Pliers, Screw drivers

With the oven dial at OFF, the oven would turn on by itself every 5 to 10 minutes and it would heat up to about 100F and shut off.

Unplugged the range. Took out all the necessary screws and lifted up the cooktop cover. Unscrewed each gas tubes connecting to each gas burner's dial to allow more working space. Pulled out the old thermostat, installed the new one. Put back the gas tubes and all other necessary screws. Plugged the range and tested out the new thermostat.

Was this instruction helpful to you?

Customer:: Janet from Jessup, PA
Parts Used:: WB28K10190, WB28K10189
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers, Socket set, Wrench (Adjustable)

Bent/Broken Front Orifice Tubes

I removed the two nuts that secure the rear orifice tubes. This allowed me to lift the range top to access the broken tubes. Once lifted I removed the nuts that held the broken orifice tubes. I then connected the new orifice tubes. I removed the three(star)screws that fasten the orifice brackets under the range top. Doing this allowed me to connect the new tubes without having to maneuver them at all. I then lowered the top just enough to reattach the brackets. After securing the rear tubes I snapped the range top back into place. Just remember, if you use propane for cooking then you must remove the brass orifices from the old tubes and place them in the new ones. If you don't do this then your flame will not burn properly. Simply unscrew them from the old tubing and put them in the new tubing.

Was this instruction helpful to you?

Customer:: Arthur from Riverside, RI
Parts Used:: WB16T10046
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Hot Spot On Burner

Replaced old burner element with new, easy

Was this instruction helpful to you?

Customer:: Rose from Edinburg, IL
Parts Used:: WB16K10043
Difficulty Level:: Really Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver, Pliers, Screw drivers

hole burned in oven burner tube. making noise

changed old burner tube , with new equipment. thanks to PartSelect.

Was this instruction helpful to you?

Customer:: Rachelle from Airmont, NY
Parts Used:: WB03K10141
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

missing knob on range

Order came very quickly and was the perfect fit. Thank you

Was this instruction helpful to you?

Customer:: Pamela S from Chesterland, OH
Parts Used:: WB20K8
Difficulty Level:: A Bit Difficult
Total Repair Time:: 1- 2 hours
Tools:: Nutdriver, Pliers, Screw drivers

Oven Heating Too Hot, More Than 100 Degree Beyond Setting

Replaced the oven thermostat and calibrated the new thermostat by adjusting the temperature setting knob. Instruction I found on-line were very helpful and the repair was moderately difficult. Trickiest part was threading the new thermostat into the oven. Total repair time about 1 hour.

Was this instruction helpful to you?

Customer:: Rudy from Waterloo, IA
Parts Used:: WB20K8
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

Thermostat knob broke off

Cut off the power. unscrewed the cover. fed the new thermostat inside the over and rescrewed. Feeding the line was the most time consuming finding the hole to insert it in the back of the oven.

Was this instruction helpful to you?

Customer:: Rick from Vanderbilt, MI
Parts Used:: WB16K10043
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

Oven would lite but sounded like JET ENG.

removed 4 screws unplugged wires Then reversed prosseces

Was this instruction helpful to you?

Customer:: Rebecca from Las Vegas, NV
Parts Used:: WB27T10469
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

no display

Turned off circuit breaker to stove, remove top panel and then the old control module and installed replacement. Power back on and top panel reinstalled. Easy!!! And Everything works like new!!!

Was this instruction helpful to you?

Customer:: John from Los Angeles, CA
Parts Used:: WB16K10055
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Burner would not ignite.

Could not have been simpler. Burner head dropped into place and was held in place by gravity. Not possible for part to go in incorrectly.

Was this instruction helpful to you?

Customer:: James from Monterey, TN
Parts Used:: WB08T10026
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver

broken light socket

The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.

Was this instruction helpful to you?

Customer:: Joseph C from Williamsport, IN
Parts Used:: WB20K8
Difficulty Level:: Really Easy
Total Repair Time:: 30 - 60 mins
Tools:: Nutdriver, Pliers, Screw drivers

Temperatures were much usually hotter than indicated

First of all I had to find the right part from Partselect, which was very easy, delivery was fantastically fast even tho I didn`t order special delivery. After reading installation suggestions on the website, it was simple, open the top, disconnect the burners, removed the thermo from the inside. The only hard part was threading the sensor through the correct hole. I had to remove a couple of cover plates to see where the hole was. Put it back together, lit the oven and the temps were correct, as shown by an oven thermometer.

Was this instruction helpful to you?

All Instructions for the JGBS23SEH5SS