JBP22*R2 General Electric Range - Instructions

super easy - unpluged stove - unscrewed old element w/nutdriver from back of stove. unwired element - discarded. wired new element (2 wires). secured new element to back of stove. pluged stove back in. works great. Ordered part on Sunday, recieved it on Tuesday- VERY NICE SERVICE

It was so easy. Just removed the cover and then unscrewed the wires (keep track of which wires go to which side). Do teh reverse to reinstall

Repair was as easy as one, two three. Turned off the power and removed the two screws holding the element in place. Then pulled the element out approx. 3 inches and removed the two screws connecting the wires to the element.

From there I reversed the process and the repair was complete in less then 5 minutes, and I am not a electrician.

Unscrewed the element from the oven,disconnected the two screws for the electrical and reverse the procedure to install new element. Took all of about 10 minutes.

Made sure oven was turned off. I used nut driver to remove nuts holding old element to back of oven. gently pulled element out of wall, taking care not to yank because of wires attached to back of element. Made sure oven was off again and then used nut driver to carefully remove wire leads from receptors on element. removed old element from oven and got the new element. carefully used nut driver to attach wire leads to new element. When snugging the bolts to leads, used pliers to keep leads on the element from bending. carefully replaced wires and rear of element into the space behind oven, and used nut driver to attach the back of element to the back of oven. shut oven and turned on to make sure it worked. it did. I was very pleased with my experience with part select dot com, and will be buying another element soon to replace the one in my other oven! Thank you

removed heating element,removed old drip pan.added new drip pan,replaced heating element.Took less that 3 min.

Using a nut driver, I removed the two screws holding the baking element to the firewall of the oven. I then pulled the baking element out exposing the two wires connected to it. I then used the same nutdriver to remove the nuts and detached the old element. I then connected the new element to the wires, pushed the wires inside the firewall and reattached the element to the firewall of the oven.
The time it took was literally a few minutes. Works like a new oven!

It was so simple, I turned off the breker to the oven, unscrewed two screws holding in the element, pulled out until the wire connetion was exposed. I unscrewed those two screws, then placed the replacement part, put the two screws on, pushed back the wiring and insulation.Final step was screwing two screws to hold the unit to the oven back. So simple! The part was ordered regular mail and still was here in 2 days. Will recommend to friends for sure!

I couldn't find the oven model number so I just looked at the shapes from partselect.com. This would have been fine except I didn't know my Kenmore model had 4" leads so the one I ordered were only 2". I had to return the first element but the process to do this was FAST and EASY. With help I found the model number and had the correct part shipped. It took less than 5 minutes to install. It took longer to mop and clean behind the oven that hadn't seen the light of day in 10 years.

Unplugged the range. Opened the range top, unscrewed the old block and cut the wires back. New mount did not match the range top. Removed the old mount from the old terminal block and removed the new mount from the new terminal block and inserted the new block in the old mount. Spliced the wires with the provided wire nuts, protected the splice with the provided heat shrink tubing and installed the burner in the new terminal block. Reinstalled the power cord and tested the burner.

Just like your example said/turn the power off to the oven/remove the screws that hold the element in place and then I pulled th element out a little ways and disconnected the wires/reconnecting took a little longer only because it was hard to see/but I connected the two wires and put the screws back in and it worked. Saved me a lot of money/my husband wanted to get a new double oven

Turned off power. Removed old broken one installed new one in minutes. Turned power on and tested it out. If this 60 something lady can do it, you can too.

Flip the circuit breaker going to oven off, then used a 1/4 inch socket on the mounting flange bolts and the bolt head screws attaching the wires. Then used a flat head screwdriver to reattach the wires with the supplied screws and bolted the new element in place. Back to the circuit breaker flipped the switch and turned the oven on to test it, and now works fine. *be sure to remove the sticker before installation, use rubbing alcohol to remove any residue.*

First I turned the Breaker off for the Oven. I removed the two screws that hold the element/cover plate. I pulled the element out to get access to wires attached to element & removed screws holding wires to element. I reversed the process to put back together.

The repair was fairly easy. Removed the 2 screws that hold the plate to the oven and then pulled out the element and loosen up the screws that connect it. Installed the new element and re-attached the element to the plate and secured the plate back to the oven. This site was very easy to use and very helpful and I will use it again if I need another part.