JGB908SEK4SS General Electric Range - Instructions

I ordered the oven rack on a Tuesday and received it the very next day - was wowed at the service.

nothing to it.

Remove bottom drawer,open oven door,take oven racks out,use flat tip screwdriver to remove two screws in back of oven. Then remove cover over burner and igniter.Reach under oven and unplug igniter,while down there use 1/4 inch nut driver and remove two screws holding burner. Then remove one screw inside oven in front of burner. Pull burner and igniter up and out of oven.I did not unplug stove or turn off gas some people may want to,if you have to move stove out to work on it

could not even attemt installation due to messed up parts delivery

Husband actually did the repair, It went really well except he forgot to remove the heat shield from the old part to attach to the new bottom. (His mistake!)

The whole process was very easy! I just got the model number and bought a new rack and silverware holder on,one. There was no assembly needed so I just popped them in and replaced the old ones! Very easy to do!

Part was purchased to replace damaged elbow. During the conversion to LP gas the elbow threads were stripped from over tightening the collar nut. To accomplish the replacement: 1. remove 2 sheet metal screws holding protective shroud in place. 2. disassemble the compression fitting CAUTION DO NOT OVERTIGHTEN 3. loosen elbow collar nut if necessary and remove elbow. 4. reassemble starting with the compression fitting. 5. connect the elbow to the broiler burner with the collar nut 6. tighten all the way down turning nut cw for LP conversion CAUTION DO NOT OVER TIGHTEN 7. with broiler on adjust flame and check for leaks

You first must remove the burners on the cooktop to gain access. They are secured with 2 Torx screws which are accesiable after removing the burner covers. The igniters wires must also be removed which simply are push on connections. The cooktop must be removed by inserting a scredriver on each corner of the cooktop from the front. They simply push in and the entire top lifts off. Remove 4 screws covering an access panel located in the front of the cooktop to gain access to the motor/latch, which is secured by two screws accessiable from opening the oven door just below the latch. Replace motor/latch and reassemble. Carefull with the wiring as the replacment switch has been changes. The wires on the left switch of the old assembly get connected to right switch on the new assembly, and the right side wires on the old get connected to left side on the new. Reassemble and Viola!

called appliance repairman. He found problem and ordered new part. After 2 months waiting for part to get there, my husband got on internet and calld your number, and ordered what was needed. Now for the great thing. Within 4 working days we received what we thought we needed. but we had ordered the wrong part number. Got back on internet, went right to your web site, found the part that we did need, a flame spreader instead of the Deflector. called your service number, talked to a very nice person, again, told her what we did and ordered the correct part. Another great thing, we got that part the very next day. I returned the wrong part that same day. We then had our son install it and now we have a very nice working oven. Though out this very long ordeal, we talked to the applicance service people and got the same answer. The part has been ordered and it should be here next week. When we found your web site and called for the part, I called the appliance service and told them we had ordered the part ourselves and I would be happy to give her this information. THE VERY NEXT DAY she called us to tell us the part had fially arrived and they could come out the next day. Told them sorry but it as already taken care of. The very next time we need some part for any appliance we will call you first. Thank you for your very nice service people and the fast way that this all took place.

Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.

I opened oven and pushed oven rack inside.

I removed the bottom drawer, oven racks and bottom cover inside over, removed the screw at the front end of the burner. Unplugged the wire connector for the igniter. Removed the two retaining screws from the burner tube, removed from oven. Removed mounting screws from igniter to use on the new tube and igniter. Wire terminal did not match. Cut wire connector from old igniter, cut wire connector from new igniter. install old connector on new igniter with wire nuts.Install burner tube in oven. Connect igniter connector together. Reinstall over cover and racks. install bottom drawer. Turn on oven. Yah. It works. Their was a hold burned in the old burner tube causing the popping noise and finely not operating. Good to go. Bruce L Best Sr

Easily glide in.

Installation was very quick and simple. Removed wire connector for the igniter then hex screws for the bake tube. Attached the new igniter to the new bake tube and reinstalled in oven. 15 mins. I took the extra time to clean the oven pan and heat shields. Removed old charred baking spills and grease buildup. Oven is 12 years old and working like brand new.

Replaced the burner and igniter after watching the repair video provided by Partselect. I was pleasantly surprised when the parts came the very next day. It was so easy and the igniter plug matched perfect. My wife wanted to hire a repair man but I did the repair and saved a bundle on the labor. I couldn't be happier about my purchase.