JBP30AB2AA General Electric Range - Instructions

couldn't get exact fit--out of production. mounting bracket at back of range for new element too small. took bracket off old element. cut down bracket on new element with tin snips, drilled holes thru it and old bracket and screwed together. at this point the new element was to long & touched oven door. removed spacers that came with new element (used old support to attached to roof of oven) and pried elements apart (which made element wider & shorter). working good.

I just follow Steve's Installation Vidio. My range works.
Thanks Steve

replaced lights in refrigirator and freezer

Only instructions I have has nothing to do with installation. But I'd like to suggest that you find a better shipping method. Placed my order on Feb. 7, received message later same day that it'd shipped. I didn't receive it until Feb. 16th -- very poor delivery service.

I just inserted the replacement where the old one had been connected. It took less than 5 minutes. It was so simple & easy that 'repair' is too generous a word -- & I am NOT handy, in any sense of the word. It took me longer to figure out where to find the model number!

Easy repair, just had to take the damaged burner out and slide the new burner in....

Simple to repair. Take off the cowling around the burner element on the stove top and pull out the old element. Slide in the new heating element with the cowling paying attention to the three spoke support areas on the stove burner frame. Very simple. A 5 minute repair. No tools required.

Cut 4 inch’s off the new terminal block wires then using my wire strippers stripped 1/2 inch off the ends , the old terminal block wires I stripped 1/2 inch at the ends using a wire nuts on both wires and electrical tape connected the terminal block to the stove plugged the new burner in and the burner worked 100%.

Took back off and replaced.

Would have helped it I knew the push on terminals of the bake element were visible and accessible to slide the terminals on from the back side of the stove in the beginning. There is not enough slack in the the terminal wires to connect them from the oven side, so you will have to open the back panel to retrieve a wire anyway. SO, CONNECT THE BAKE ELEMENT TO THE OVEN WALL FIRST ! Then, open the back panel of the stove and simply slide the terminals on the exposed slide terminals of the bake element.

The only hard thing was contorting my old beat up body and joints long enuff to reconnect the 2 wires and oven heat sensor and put in 6 screws with a 1/4" nut driver. I did remover the oven door and that made it much easier for me.

I too made the mistake of cleaning the oven with the shelves in place. It doesn't really harm them...but they turn a tarnished brown color...they look dirty. These replacement shelves were a perfect match. Pricing was reasonable, communication was terrific and shipping was super fast. Happy camper here :-)

Ordered the bake element part from partselect.com. When the part arrived I removed the 2 6mm screws from the element, I used two clips to hold the wires in place so that they didn't receed back into the stove. I installed the bake element, installed the two scews ans was done. It took all of 10minutes.

Lily in Florida

First I cut the circuit at the breaker, and then pulled the range from wall to access the access panel. This top panel was held with 4 screws and removable with a standard phillips head screwdriver.

I then removed the 5 wire-crimped fasteners from the defective surface burner switch. (I first labeled these wires to ensure correct placement to the new switch). There were an additional two screws behind the corresponding knob that needed to be removed in order to completely remove the old switch.

The new switch was installed in reverse order to the steps indicated above (two screws behind knob, 5 wire-crimped fasteners, 4 screws to panel). Range was pushed back into position and breaker turned on.

Unplugged the power supply. Took off the cover on the back of the unit. Unplugged the wires to the broiler element. Removed the bolts(4) holding the element inside the oven. Removed the temprature sensor from element and took it out. Put it all back the way it came out. Worked great. Took 25 minutes.