JBP63BB1AD General Electric Range - Instructions

unpluged unit then removed back panel unpluged element then took the two screws out took old element out replaced with new one put screws back plug element back in put back panel on pluged it in and started baking home made chocolate chip cookies

The very first thing we did was turned the circuit breaker off and unplugged the range.
My husband removed the back panel and unplugged the switch. Drew a diaghram of the color coded wires. When we received the new one he broke the extension bar off to fit the knob, plugged it in and we were back in business. It was very easy for my husband as he is a mechanic (millwright). However, if you are mechanically inclined it is an easy fix.

Remove two screws with nut driver that holds range top down. Turn off breaker or unplug before lifting top. Brace top with 2x4. Take picture with cell phone just in case. Orient replacement part with old burner. Remove one wire at a time and install on new burner in corresponding correcting terminal. be sure they are snug. Drop top install nuts . Test! Done! I am not an electrician!!!!!!!! Please do not publish !!!!

lift stove top, 2 undermount screws. Then unplug 4 wires, I did them 1 at a time plugging into new burner as I go so I wouldn't screw up. Take 2 screws out of old burner to stove top, # all around circle put screws in same # on new burner.Done Good experience all the way around. Order delivery and install

Turned off juice
Pulled stove from wall
Unscrewed 2 screws to loosen range top
Lifted n propped top
Unplugged 4 wires
Unscrewed burner assembly
Installed burner-reversed steps to reassemble

Flipped off the breaker for the stove. There were two screws holding the old element in place. Removed those, pulled the element out a little to expose two wires, disconnected those, swapped in the new element, reconnected the wires, and screwed it back into place. Flipped the breaker back on and voila! Barely more difficult than changing a lightbulb.

Disconnect stove electrical connection. Removed 2 bolts common to the upper stove top cover. Disconnected 4 wires from burner element along with 2 retaining clips.
Removed burner element and replaced with new element. Reinstalled 4 wires and 2 retaining clips. Lowered stove top cover and reinstalled 2 bolts. Connect stove electrical to wall outlet. Turn on burner element and verify that it works.

Easy

While I appreciate all the various parts available from PartSelect, I was disappointed that the only heater element that was approximately the right size and shape for my wall oven had push-on prongs. My original was screw-on.

Thus, I had to (very) carefully drill through the somewhat thick metal tabs to get screws into them. This meant holding the tabs with a pliers while I drilled them out to make sure that I did not break off the tab. Then, I increased the hole size by using increasing diameter drill bits. I let the screws self-tap, but again this was done carefully to avoid breaking off the tabs. Finally, I found that the part of the new heater element going through the back wall of the oven was an inch or so longer than the original. This did not seem to cause a problem of overheating outside the oven. At least not so far!

It was so simple looking, I had it shipped to the tenants of the house. They swapped it out easily, and were happy to get back to baking.

I followed the easy instructions and everything went well. I had the new switch installed in about 30 minutes. My wires were different colors than on the instructions but it was still easy to figure out where the wires went on the new switch. Just do not be in a hurry and make sure you measure before you break off the extension bar. My knob fit on the new switch without any of the parts that came with the switch.

popped the new one on!

Of course the first thing is to turn off the breaker, Unplug the appliance, pull the two electric feed wires off the old element. Then remove the four screws that hold the fan guard in, After that the two screws that held the Bake Element in place. Then reverse the process to install the New Element. Took about twenty mins. from start to finish. Just Like New. And thanks to Parts Select for their prompt service, Had the new part in two business days.

saw when heating the stove up the bottom element wasn't getting hot. got part number and looked up online and ordered

First I shut off the power at the power box. Second I removed two screws in metal plate. Third I unplugged the two wires. Repeated steps backwards and it works great.