JBP22DA1 General Electric Range - Instructions

Removed existing surface element and replaced with new element.

P.S.

Part Select service was excellent.

took 2 screws out removed old element, put new element in and put the 2 screws back in. All worked great and I baked bread that same day. The service was fantastic, and $40.oo cheaper than the appliance store I checked with.

OK, I put the drip pan under the burner. Without a single problem.

replaced lights in refrigirator and freezer

I first removed the unit by pulling gently from connection. Replaced the new one in that same manner - simply inserting into connection.

Very easy, I'll probably try it again soon.

This is far to simple to even be a worthy story ,other than that the cause is a bit interesting. My wife had placed a plastic cutting board and some meat into the oven to get it away from my counter-cruising dog.
Later, without remembering the cutting board she turned the oven on to "broil." Hmmmm...

REPAIR:
Open oven door
Put in new rack
Close door

I removed the screws holding the element in place and pulled it out, then pulled the wires from the element out. Very easy. When I got the new part, it seemed like it would be simple. I plugged the new wires back in and started to push it in place to screw it in. Unfortunately, there was a big spark and everything died. I was afraid I had crossed the wires, and I'm still not sure how one is supposed to tell which wire plugs in to which holder in the oven. Luckily, I discovered that I had simply blown a fuse. Problem solved, everything works.

Removed the two screws which mount the element to the back of the stove.
The old element had screws connecting the wires to the heat element. The new element needed female electro-terms, so I crimped the appropriate electro terms on. If you need to do this make sure you use the correct electro-terms based on the wire size from the stove.
Installed new element in 2 minutes.
Parts Select had the part here within two days with standard ground shipping. Very impressed with service.
A clearer description of how the part connected to the wires from the stove would have been helpful.

Because of the superb pics and descriptions on the Part Select site, I was able (with NO range model number) to order the correct range element for beloved son's stove. He plugged it in in 3 seconds, works great !

ordered over the phone a new temp sensor. Un plug the oven, take off the back, open oven and unscrew the temp sensor, pull the sensor until the elec connector clip comes through so you can unclip the old sensor, clip on the new then pull the line back and re attach the sensor to the ovn. Plug in the oven.
Pretty simple, just hard to work inside the oven. I unclipped the sensor line outside the oven to make sure it would come apart first before I was working inside the oven.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Took Switch panel off range. Disconnected Infinite switch. Reinstalled infinite switch.. Replaced panel. Repair was very simple and self explainatory.
Knott County Housing Authority Maintenance Personnel

baking element went bad. removed the 2 screws holding it in place. unscrewed the 2 connected wires. took the new element which is a plug in type and drilled holes to fit the screws. had to do this as the exact part needed is no longer made. works fine.

After staring at the online pictures of possible replacement bake elements, trying to count the number of squares to figure the length and width of available oven bake elements (some of the pics had listed measurement some did not), I settled on a push on element, since there were no matching screw in elements that appeared to come close to the measurements needed. Since it was a push on, I had to drill out the holes a bit more to fit the screws which took some time and finesse. It appears to works and it at least has enabled me to put off my bigger decision of buying a newer oven for a bit.

I followed the instructions given to me in the package and all went well. I cut the old wires off the burnt terminal block, stripped the wires, installed the wire nuts with the shrink rap, installed the new terminal block and burner. The new burner is working great! Thanks