JBP56G*R3 General Electric Range - Instructions

OK, I put the drip pan under the burner. Without a single problem.

I pretty much followed the youtube video posted under the part that I needed. Turned off electricity to that area of the house. Unplugged stove. Took out the old sensor, pushed new sensor cord through the back hole. I did put a small amount of tape,so I could pull it through from the back better. It was impossible to get the clip disconnected in the back and the new clip didn't match up correctly anyway. Ended up having to cut the wires and strip them. I twisted them together and put on the ceramic wire nuts on. Reversed ever thing I did and F3 appeared. Looked that code up on internet. It was from an open or shorted oven. Suggested I check the connections. Pulled stove out again, unscrewed caps on wires and noticed the sensor's wire had another cloth type coating on it. I gentle cut that off, twisted and capped wires again. Plugged in oven, turn on electricity, and tried out stove. Everything is working just fine. Everything took a little longer because this was first time doing this type of repair.

Took Switch panel off range. Disconnected Infinite switch. Reinstalled infinite switch.. Replaced panel. Repair was very simple and self explainatory.
Knott County Housing Authority Maintenance Personnel

Watched the video on the PartSelect site. Could not have been an easier repair and I saved the cost of a service call - probably saved at least $100 - $150 in service call and I can only guess what the labor cost would have been. Will use this business again for other appliance repairs on my older stove, washer, etc. By the way - the official Kenmore site said this part was no longer made and unavailable --- Thank you PartSelect for having the part and saving me the cost of buying a new stove!

When the part arrived, I used the diagram provided by the website to see what really needed to be done. Keep in mind, if you're doing it correctly and disconnect the range from the power source, it's going to be dark inside the oven. Get a good flashlight or electric lantern. There are two screws holding the element in. Mine were 8MM hex-head screws, but be prepared for anything. I removed the with a socket attachment/adapter to my cordless drill/screwdriver, and the part came right out. Some insulation will come as well - don't panic. Installation is similar, just in reverse order. Pay attention to the feet on the element. Make certain they are down. Don't lean on them when you think you're finished and discover that you installed it upside down like someone I know, and have to pull it out to correct this.

I first removed the unit by pulling gently from connection. Replaced the new one in that same manner - simply inserting into connection.

Very easy, I'll probably try it again soon.

Because of the superb pics and descriptions on the Part Select site, I was able (with NO range model number) to order the correct range element for beloved son's stove. He plugged it in in 3 seconds, works great !

This is far to simple to even be a worthy story ,other than that the cause is a bit interesting. My wife had placed a plastic cutting board and some meat into the oven to get it away from my counter-cruising dog.
Later, without remembering the cutting board she turned the oven on to "broil." Hmmmm...

REPAIR:
Open oven door
Put in new rack
Close door

replaced lights in refrigirator and freezer

Removed 2 nuts holding the baking unit to the oven back, removed 2 nuts holding wires in place, installed new unit following procedure backwards. It takes longer to get the tools,take the oven door off, and take racks out than it does to remove and replace the baking unit.

I followed the instructions given to me in the package and all went well. I cut the old wires off the burnt terminal block, stripped the wires, installed the wire nuts with the shrink rap, installed the new terminal block and burner. The new burner is working great! Thanks

No repairs, really-just replacement, but I have been looking for the burners for three and one half years, and PartSelect had exactly what I needed for this old stove!
Theyalso had the electric element that I bought in the next order.

I simply replaced the element. HOWEVER, the most wonderful parts of this repair...Because of the pictures and closeups and descriptions I knew exactly 'what' to order! And I had the replacement in less than 24 hours. I can do some home repairs but this company provided such detailed information AND speed of delivery...that this was a no-fuss fix. I'll definitely stop by to buy, again. Thanks!

We tried to find the replacement pans at the local hardware store and were disappointed in that although they were cheaper, they were not deep enough to handle the heating elements. We were delighted to find that the parts from PartSelect.Com were genuine GE parts... installed in minutes and were delivered VERY quickly!

I removed the old drip pans, cleaned the range top, washed and installed the new drip pans and put the old pans, box and packing materials in the trash. In only 12 minutes my range top looked like new and the mess was picked up. Now, if I could just get the rest of the kitchen looking that good that fast!