XCF300PM2WW General Electric Range - Instructions

easy, less then 15 min. but take off door first makes alot easier. and don't forget to unplug, like i did. just a few sparks but no damage thank god.

I removed the burners, took the old drip pans out, put the new ones in and put the burners back in. This was so easy that a caveman could do it.

Turn off power to oven. Removed the rack. used a 1/4" nut driver and removed the two screws holding the element to back of oven. Slid the element out, unhook the two wires clipped to the end of the element. Replaced it with the new element, installing it in reverse. Took about 15 min. Rememer to turn off power to oven before attempting to work on it.

Remove lower drawer and contents. Unplug unit. Tilt range on its back for easy access. Tie open oven door to forward legs with sturdy rope. Use small socket to remove 2 back screws and 2 forward element hanger screws. Detach broiler element connections from wire clips(2). Insert new element, attach 2 new connections to clips first. Install back socket screws. Install front socket screws for element hanger. Slide in oven shelves. Release oven door rope. Lift range to normal position. Replace lower drawer. Plug 220 in. Test oven element then broiler.

Disconnected the plug from the receptacle; removed the 2 screws holding the element in place at the rear of the oven; removed the support bracket at the front (also 2 screws); removed the panel on the back of the range; pulled the wire clips off the element (had to replace one of them); slid the new element in place; reconnected the wires and fastened the element in place; reattached the support bracket and rear panel ... With the assistance of my wife (extra hands) this was an easy job!

Removed element with 1/4 " nut driver, unhooked element,started to install new element and discovered the wires were too short and had to remove cover on the back to replace wires on the new element. The wires on my range were not as long as the ones showed on the video.It was still an easy repair and the delivery time was less than 2 days. excellent service. Thanks

Purchased the board installed it and saved about 130 dollars.

Took out the old control module and removed the sticker and reattached sticker to new part and installed the plugs, put the screws back in and it started working, thankyou so much.

It was easy to replace it. Just remove the screws and unplug each wire and plug them back. The problem was to take off the plate cover that has the printed letters on. The plate cover cost more than the Electronic Control Board.

My Range had the issue I mentioned here. I put off the repairs for a long time, but Thanksgiving was around the corner and we needed a working oven. I had made a previous call to repair man and was quoted $75.00 for a service call to come and check the issue. Before calling a repair man back, I decided to pull the rear cover off the range to see how complicated it would be to repair. I removed the rear cover and found that everything was connected to this "Oven Electronic Control" except for the top elements (explaining why they still worked and the oven didn't). This made it seem that this part would surely have to be causing the issue. I did a search on Google and found this company and the part that I needed. The cost of the part was less than the service call for a repair man would have been. I ordered the part and paid for next day delivery. The part shipped on Monday and arrived on Tuesday. For the installation, I had to identify the wiring because the connector layout was a little different. When I looked closely I found that the terminals were numbered the same as the old part. I replaced wire for wire, put it all back together and tried it out. It worked like a champ. I was thrilled to have been able to find the part with schematics on this web site and it was the correct part and fixed the problem. I was also thrilled that I saved a couple hundred dollars fixing it myself and that it was so easy. I would highly recommend this company for the ease of use of finding the part on their web site, the reasonable price and their prompt processing and delivery.

I miss diagnosed the situation at first. When the top element only heated up I thought the control was the problem. Wrong. Apparently both elements heat up during initial start up. It turned out that the bottom element was not working so it needed to be replaced rather then the control. Now both are replaced and the oven is now back to original status. Entire repair cost about $80. I saved over $100 by attempting this myself. Easy fix. Obviously I am not a pro. My local hardware store had a generic heating element that worked just fine and only cost $22. Two screws to repair after removing the back panel. Remember to pull the plug before you begin and after the repair put all panels back on before plugging back in. Pizza anyone?

ordered part shut electricity off took out 2 screws took of connectors put in new element replaced connectors replaced screws turn on elec started cooking

Moved stove out away from wall .Unplugged stove, turned gas off. Unit is a dual fuel convection. Burners are gas, oven is electric. Removed 4 screws from back shield and exposed the 2 electrical leads connected to broiler element. Disconnected the electrical .Inside oven I removed the front bracket holding element in place, then removed the 2 1/4 screws in the back holding element in place. placed new element in and finger tightened the 2 screws, next I installed the front bracket and finger tightened those. I then snugged the rear screws in followed by the front. I went to the back and reconnected the 2 electrical leads. Replaced back shield and plugged unit in and turned gas back on.Caution; Make sure your gas line is flexible before moving your stove out to far. Repair was very easy

My oven is wired into the wall so I had to cut the power off at the fuse box. The hardest part was pulling the stove/oven away from the wall to see if it was a simple plug in or wired in. I lifted bottom drawer out so I could get leverage and lifted the entire unit so I could put the front feet on the soft pads. It slid away from the wall easily. I found a socket that fit the screws on the plate holding the broken element and unscrewed it, saving the screws. A gently tug on the element pulled the attached ends through the hole. The tip of the ends were attached to the wall wiring by a small sliding metal clip. I carefully pulled the ends apart. One was hard to get apart to I had to push it with the tip of a knife. Once the old was off the new was super easy to put back on. Side the tips to the clips, screw the plate in place and push the oven back in place. Flip your fuses and turn on the oven. Yeah!

followed the instruction from your video an it was a snap