JB988KH4CC General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Brighton, MI
- Parts Used:
- WB07X32931
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
rust on outside bottom of door.
It is first necessary to remove the door from the range according to the manufacturer's instructions. Once removed, lay it down on a flat, protected surface with the outside facing down. Remove the two upper phillips screws and the hex nuts on the bottom channel. Next, separate the inside panel from the outside panel. You will then see the remaining hex nuts that have to be removed in order to replace either the bottom trim channel or the side pieces.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Harkers Is., NC
- Parts Used:
- WB21X22134
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven slow to heat up
Removed oven door. Removed 2 screws from heat sensor on rear upper wall of oven. Pulled unit out to access rear of unit. Removed six screws on shield on back of unit. Dis connected heat sensor wire and pulled old sensor through from inside of oven. Feed wire of new sensor through from inside and plug in. Everything in reverse. I also had the gas(propane) company come out and check the pressure coming out of the "low pres." regulator. It was low, they changed the regulator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- daniel from gap, PA
- Parts Used:
- WB21X22134
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
f-2 or f-3
remove two bolts in on sensor and slip thru back un plug and reverse to put in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Boynton Beach, FL
- Parts Used:
- WB07X32931
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
rusted door bottom channel trim
very easy, door comes off without any tools. youtube has instruction for that. seperate the innerdoor pannel to access the screws for the trim.6 screws holding the trim. the hardest part was cleaning the rust off.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lynn from sunnyside, NY
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
F2 reading
Followed the instructions that were sent to me by E-Mail.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Shakopee, MN
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Stove drawer rear guides broken
Installed new guides with a nut driver without any problems.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Lansdale, PA
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Hard to move drawer in and out because the rear drawer supports broke off.
Repair was very easy - less than a few minutes - just had to screw in 2 screws to the new drawer supports.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen from Munt Laurel, NJ
- Parts Used:
- WB20T10024
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Oven Probe broke
Ordered new probe
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Salem, OR
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Flashing F2 and erratic temperature readings.
Unplugged from wall outlet, then opened oven front door. Reached in and removed two screws. Pulled oven sensor threw and detached electrical connector from old sensor. Plugged in new oven sensor and reversed removal procedure. No more Flashing F2 and oven temperature came to ready. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Woodinville, WA
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Our bottom drawer support broke and the bottom drawer was canted
Simply removed drawer and lined up the newsupports. Made sure the guide pin was lined up and installed with single screw
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Stuart, VA
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic slide for storage drawer broken.
Took part out of package, looked at instructions and followed them. Required a screwdriver to screw part on to the drawer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Lisle, IL
- Parts Used:
- WB21X22134
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
oven not warming, f2 indicating overheat
Removed 4 screws from back panel, disconnected small electricsl connector from sensor, removed one mounting screw from sensor inside oven,pulled wires through and removed old sensor. Fed wires for new sensor through and connected electrical connector, installed panel, installed mounting screw on sensor and checked oven, worked like a champ. Took 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Newark, DE
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Range lower drawer would not stay on track.
Easy to install replacement parts using the screws provided.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mario from Deer Park, WA
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broken drawer support
Followed the example picture on the part bag. Anyone could do this, incredibly easy. Took about 4 minutes to install both sides.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from Yonkers, NY
- Parts Used:
- WB04T10022
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Needed to replace the door gasket on my range
Went super fast--very easy. Part fit perfectly and the installation was a snap.
Was this instruction helpful to you?
Thank you for voting!