JGBC17PEA2WH General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Alphonse from Glendale, AZ
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
We had to buy two dubble burner assemblies because one burner was out on each old assembley
The burner assembly was for my wifes daughter. She raised the top of the stove removed the old burners and set the new ones in place she also used the set washer and it works just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Forestville, CA
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The double burner assembly had years of gunk so the burn was not clean.
The old double burners lifted off. Before the new burner could be set down into place, the area had to be completely cleaned using a flat blade screwdriver and damp rag. This allowed the new burners to seat properly in place. That is it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from Payson, AZ
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burners were not burning properly
Just removed the old and set in the new. Waalaa. All is well now. The web site, ordering, shipping and all was super easy.
Thank you
Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Omaha, NE
- Parts Used:
- WB15X10048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Orignal oven door handle had multiple fractures and was fast becoming useless.
Removed the old handle with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- albert from La Veta, CO
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Back burner not working
Lift stove top, rest it on the pop out holders on stove.
Take old double burner out, Make sure gas port is not plugged.
Put new burner in its place. Make sure it is solid, if not use the washers sent with new burner. turn on gas to burner, to see if it works. Close stove top an wa la!
The bride is happy.;-]
Take old double burner out, Make sure gas port is not plugged.
Put new burner in its place. Make sure it is solid, if not use the washers sent with new burner. turn on gas to burner, to see if it works. Close stove top an wa la!
The bride is happy.;-]
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Birgit from Opelousas, LA
- Parts Used:
- WB16K10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burners were dirty and wore out
Unplugged the old ones. Cleaned the stove top. Plugged in the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kevin from West Roxbury, MA
- Parts Used:
- WB03K10036
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Numbers removed from knob when cleaned
After receiving the new knob and installing by pulling off the old one and with a little pressure applied, I just pushed the new one into place. With the new knob installed I turned the oven to 350 degrees' putting an oven thermometer into the oven and waited for it to turn off at the end of the pre heat, then matched the knob temp with the thermometer by pulled the handle back off and with the two small screws on back side of handle loosened I adjusted the handle to match the over temperature tighten screws reinstalled
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Alameda, CA
- Parts Used:
- WB20K8
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
With the oven dial at OFF, the oven would turn on by itself every 5 to 10 minutes and it would heat up to about 100F and shut off.
Unplugged the range. Took out all the necessary screws and lifted up the cooktop cover. Unscrewed each gas tubes connecting to each gas burner's dial to allow more working space. Pulled out the old thermostat, installed the new one. Put back the gas tubes and all other necessary screws. Plugged the range and tested out the new thermostat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pamela S from Chesterland, OH
- Parts Used:
- WB20K8
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Oven Heating Too Hot, More Than 100 Degree Beyond Setting
Replaced the oven thermostat and calibrated the new thermostat by adjusting the temperature setting knob. Instruction I found on-line were very helpful and the repair was moderately difficult. Trickiest part was threading the new thermostat into the oven. Total repair time about 1 hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rudy from Waterloo, IA
- Parts Used:
- WB20K8
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Thermostat knob broke off
Cut off the power. unscrewed the cover. fed the new thermostat inside the over and rescrewed. Feeding the line was the most time consuming finding the hole to insert it in the back of the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Burlington, OK
- Parts Used:
- WB20K8
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Oven Would Not Turn Off
Opened up the top of the stove using a screwdriver. Lifted it up about 3 inches and legs popped out on each corner and held it in that position. Traced the wire to the back and down to the oven. Pulled new thermostat along that route. When I got to the back it was a little tricky moving the thicker end around and down into the hole without removing anything from the back- but I did manage to do it. I then unhooked old thermostat from 2 clips, inserted new one and then went to the front and unsrewed the 2 small screws behind the oven control knob. Magnetic bit on screwdriver is a must! Pulled it back and removed wires one at atime and put onto new unit, then screwed it back in place and replaced knob. Plugged it in and turned it on. It came on ,stayed lit. Turned it off and it stayed lit- surprised me. . . . . . 25 Seconds or so and it went out. . . . . Job done!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from harrisburg, PA
- Parts Used:
- WB20K8
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Would Not Turn Off
I read the instructions from other peoples repairs. One note: unplug stove, and turn gas off, remember where wires go. I didnt have to remove top of stove completly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gracie from New Orleans, LA
- Parts Used:
- WB16K10026
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Burners on a gas stove did not work
Ordering from Part Select was very easy. I simply put in the model number of the stove and the replacement needed popped up and explained why I might need this part. Got a professional install because I was not at the location where the repair was needed. Will use Part Select again. The ordering experience was great and delivery was quick and easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Geneseo, NY
- Parts Used:
- WB20K8
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven would not turn off even though knob was turned off.
Unplugged stove. Removed the top rear panel to see where the thermostat cable fed into the oven. Left the current cable in place and fed new cable along side the old one. Pulled out the old cable once new one was installed. Attached wires to new thermostat and installed. Turned oven on to test. Everything went great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph C from Williamsport, IN
- Parts Used:
- WB20K8
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Temperatures were much usually hotter than indicated
First of all I had to find the right part from Partselect, which was very easy, delivery was fantastically fast even tho I didn`t order special delivery. After reading installation suggestions on the website, it was simple, open the top, disconnect the burners, removed the thermo from the inside. The only hard part was threading the sensor through the correct hole. I had to remove a couple of cover plates to see where the hole was. Put it back together, lit the oven and the temps were correct, as shown by an oven thermometer.
Was this instruction helpful to you?
Thank you for voting!