XB625DKAWW General Electric Range - Instructions

Took part out of package, looked at instructions and followed them. Required a screwdriver to screw part on to the drawer.

Went online looked up model no and found Part No. and ordered it couple of days It came in mail Cut power to oven took knob off two screws back panel. wired new switch like the old one replced thwe switch and two screws and panel connected the power tried new switch it worked great.

Removed 4 screws from back panel, disconnected small electricsl connector from sensor, removed one mounting screw from sensor inside oven,pulled wires through and removed old sensor. Fed wires for new sensor through and connected electrical connector, installed panel, installed mounting screw on sensor and checked oven, worked like a champ. Took 5 minutes.

Disconnected the appliacnce from the power source. Using screwdriver, removed the back panel and disconnected every wire that are connected to the switch. Pulled out the front nob and removed the switch. Then install the new switch by screwing it back in. Place all wires back and back panel. Connect and finish.

Remove range top [ten phillips screws] remove electrical connectors and lift out burner. Reverse procedure for installation.

I unpluged the stove pulled it out and took the 6 screws off the back to get to the switch. Around front take knob off and removed the two screws holding the swich in place and pulled it out the back. Pulled one wire at a time off of the old switch and replace on the new switch. Nothing to it had it done in just a few mins.

Took door apart to clean inside of glass door. scraped most of the wax from the stove 99%. Could not get the last 1%. Cleaned all parts. Put door back together again, put the door seal on after I got the right one. Had to reorder a new seal(one that was actually made for that model) messed up the first one and whalla! Took about 3 weeks to clean off the wax from stove and the surrounding area. Stove is good as new. Thanks for the quick service. Would definitely recommend and use you guys again. Thank You.

Removed the power plug from the wall, screwdriver and small socket allowed me to remove the front control panel. Once I located the pilot light I pulled off the holding clips and placed a new light into the holding clips...problem solved.

The burner light did not turn off, and the rear burner stayed hot. Unplugged unit and removed switch, which turned off the "burner lit" lamp. Thus I figured it was the switch that was causing the problem. Ordered the switch (I think around $18 and plugged it in. I think there were 4 screws to get the panel off, and then another 2 to get the switch off. When I plugged the unit back in (it had been unplugged while I waited for the part to ship) it beeped for a while. I had to turn the breaker on and off, and that solved the beeping problem.

Turn off power at main electric panel/ move stove away from wall and unplug cord from outlet. Take knob off the front take two screws off the panel, take back panel off and remove the used switch and take and replace the wiring to the new one , one at a time wire for wire. Then put back tighter in reverse of the way you took it off. Plug in cord and move stove back to the wall. Easy

watched it on parts select this is a real fast and simple install took longer to pull the range out of its position well started by shuting off the power then double checked that the range was deenergized removed the knob then the 2 screws then on the rear of the range removed the back panel about 8 screws used a nut driver then removed the old switch removed each wire one by one and pluged each wire into the new switch just as they were on the old switch the new switch was exactly the same so every thing matched up perfect installed the screws to the front which hold the swich in place then the back cover turned on the power and tested the switch every thing working ok done shut off power slid range back into its place turned power back on everything still ok

Directtions were by diagram only, no written instructions. Drawing was small and difficult to follow but the repair itself was easy.

Removed oven door. Removed 2 screws from heat sensor on rear upper wall of oven. Pulled unit out to access rear of unit. Removed six screws on shield on back of unit. Dis connected heat sensor wire and pulled old sensor through from inside of oven. Feed wire of new sensor through from inside and plug in. Everything in reverse. I also had the gas(propane) company come out and check the pressure coming out of the "low pres." regulator. It was low, they changed the regulator.

Disconnect the range from the mains. Open the door. Remove the single screw holding the temperature sensor - this is located on the back wall on center and is screwed to the broiler mounting plate. Remove the four screws holding the boiler element and allow it to hang down on the wire; this exposes a space to feed the wire through later. Now move to the back of the range and remove the six screws that hold the central cover plate. Now push the insulation to up out of the way and you can disconnect the temperature sensor, pull it out through front, insert the new one and connect it. Reassemble in the reverse order. Mine worked perfectly!

remove two bolts in on sensor and slip thru back un plug and reverse to put in