JGSP44WEY9WW General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Carolyn from MASON, MI
- Parts Used:
- WB21X5301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Alarm would sound whenever oven turned on - with an error message code
Watched the video on the PartSelect site. Could not have been an easier repair and I saved the cost of a service call - probably saved at least $100 - $150 in service call and I can only guess what the labor cost would have been. Will use this business again for other appliance repairs on my older stove, washer, etc. By the way - the official Kenmore site said this part was no longer made and unavailable --- Thank you PartSelect for having the part and saving me the cost of buying a new stove!
Was this instruction helpful to you?
Thank you for voting!
key pad shot an F-3 fault code bad oven sensor
ordered parts WB21X5301 oven sensor and 2 WB1X681 screws mine were bad highly recommended slid my stove out also a good time to clean all the years of junk behind it removed screws mine were bad unplug the connector slide the sensor cable through the hole and u are good after cleaning be hind stove slide back into spot reinstall power and code went away tested different temps with temp gauge and keypad and we were good
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from AKRON, PA
- Parts Used:
- WB21X5301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Intermittent heat then no heat on oven element
With multimeter checked resistance of oven sensor. Specs called for 1100 ohms. It was off by 27 ohms. The sensor from Part Select had exact wire connection as original. Then just matter of undoing old and reconnecting with new one.
One unsatisfactory event. I asked Part Select why my clock did not work or light up(timer works ok) . Answer was: sorry we have no time to help you. That soured the otherwise happy experience.
One unsatisfactory event. I asked Part Select why my clock did not work or light up(timer works ok) . Answer was: sorry we have no time to help you. That soured the otherwise happy experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sara from AURORA, IL
- Parts Used:
- WB31K5079
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Scratches in drip pan from improper cleaning, spills during cooking.
The replacement part not right size for the porcelain cone for gas. Had to unscrew 2 screws remove the cone, after unclicking gas wire. The gas spreader did not fit with the cone in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from las vegas, NV
- Parts Used:
- WB13X46909
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Sparking at 2 different burners all by themselves
Replaced Spark Module and adjusted igniters
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leon from Lancaster, CA
- Parts Used:
- WB31K5080
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
worn burner bowl.
I received a defective part from PartsSelect.com. After contacting their Customer Service, they promptly replaced the part for no charge at all. I am very, very pleased with PartsSelect.com and recommend them to all "home mechanics".
The bowl was replaced by removing two screws, removing the igniter wire, clip, and igniter. Reverse to re-assemble. I would recommend replacing the gasket at the same time.
The bowl was replaced by removing two screws, removing the igniter wire, clip, and igniter. Reverse to re-assemble. I would recommend replacing the gasket at the same time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CASPER, WY
- Parts Used:
- WB21X5301
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Bad sensor
By myself
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HAROLD from Tucson, AZ
- Parts Used:
- WB21X5301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Just follow the enclosed instructions
Followed the instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Germantown, TN
- Parts Used:
- WB57T10111
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Glass outer door was shattered, needed to be replaced.
Took the frame off of the oven.
attached the outer door to the frame while keeping it flat.
Replaced the frame.
attached the outer door to the frame while keeping it flat.
Replaced the frame.
Was this instruction helpful to you?
Thank you for voting!
The burner bowls were discolored
Real simple to do. Simply remove the two screws holding the bowl and disconnect the electric wire. Obviously first pull the power cord to prevent being shocked.
Re-attach the power cord and and screw the bowl tight. Plug in the power cord.
Re-attach the power cord and and screw the bowl tight. Plug in the power cord.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from Olympiaq, WA
- Parts Used:
- WB13T10001
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Wrench set
broiler was not lighting all the time
the broiler would light once in awhile and it appeared that the igniter was working. But it wouldn't let enough current through to open the gas valve. The nuts holding it on broke off but drilling them out and replacing with two sheet metal screws worked ok. Don't know how that will hold up to the heat though. The wiring was easy to connect ( wire nuts) but the lead wires from the stove are not that long so all the operation had to be done way in the back of the oven enclosure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from San Bruno, CA
- Parts Used:
- WB31K5079
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Remove and replaced cooktop stove tray
Easy, just remove two top screws, unplug the igniter wire and then do it in reverse. Your're done in less than 15min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Knoxville, TN
- Parts Used:
- WB13X46909
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The spark module would constantly spark
I ordered the spark module and replaced it which was veru simple, plugged it in and it sparked only now and again. I finally said forget it and it has now stopped sparking but for how long I do not know.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Chicago, IL
- Parts Used:
- WB31K5079
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
drip bowl porcelain was chipped
replaced drip bowl removed 2 screws, removed wire from igniter. and could have used a new gasket but I used some rope caulking to cushion the pan with the glass top which worked very very well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Houston, TX
- Parts Used:
- WB31K5079
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Chipped Paint
Removed two screws holding drip bowl in place. Removed spring clip holding igniter to drip bowl and removed igniter. Installed igniter to new drip bowl and installed drip bowl to cook top. Took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!