RAS240DM3WW General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Richmond, VA
- Parts Used:
- WB31K10265, WB31K10266
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed new burner bowls
No repairs, really-just replacement, but I have been looking for the burners for three and one half years, and PartSelect had exactly what I needed for this old stove!
Theyalso had the electric element that I bought in the next order.
Theyalso had the electric element that I bought in the next order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandy from Olney, MD
- Parts Used:
- WB31K10266, WB31K10265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The original drip pans had rusted and needed replacement.
We tried to find the replacement pans at the local hardware store and were disappointed in that although they were cheaper, they were not deep enough to handle the heating elements. We were delighted to find that the parts from PartSelect.Com were genuine GE parts... installed in minutes and were delivered VERY quickly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Suzanne from Brigthon, MI
- Parts Used:
- WB31K10266, WB31K10265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the drip bowls were a mess- rusty and beyond cleaning
I removed the old drip pans, cleaned the range top, washed and installed the new drip pans and put the old pans, box and packing materials in the trash. In only 12 minutes my range top looked like new and the mess was picked up. Now, if I could just get the rest of the kitchen looking that good that fast!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobby from Trinity, TX
- Parts Used:
- WB31K10266, WB31K10265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old wore out parts
just put in the new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angelo from Phoenix, AZ
- Parts Used:
- WB31K10266
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
drip ban needed replacing
removed heating element,removed old drip pan.added new drip pan,replaced heating element.Took less that 3 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Bar Harbor, ME
- Parts Used:
- WB31K10266
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Burned/scorched corroded drip bowl
No brainer. No tools. Remove burner, lift out old drip bowl, drop in new one, plug in burner, voila! Done. 10 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roscoe G from ROCHESTER, NY
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Light burnt out.
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bet from Bothell, WA
- Parts Used:
- WB31K10266, WB31K10265
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
the burner trays just needed replaced for an 85 year old senior citizen
Removed burner trays, pulled out heater unit, cleaned up inside of area around all four burners, slipped the burner trays back in and pushed the heater unit back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda L from Naples, NY
- Parts Used:
- WB31K10265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rusted out drip pan
unplugged the element took the old pan out and put the new one in, plugged the element back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lucille from HAPPY CAMP, CA
- Parts Used:
- WB17T10006
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
burner was not heating
unplug it and plug the new one in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- QUANG from LANCASTER, PA
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
ONE OF SURFACE BURNER NOT WORKING
I UNPLUGGED THE WIRE, ASSEMBLE THE BURNER ELEMENT KITS
LIFTED UP THE SURFACE BURNER PANEL,
OPENED THE BACK RANGE COVER,
UNSCREW THE NUT HOLDING THE BURNER CONNECTOR, DISCONNECT THE REPLACEMENT WIRES ON THE BACK PANEL
TRACE THE NEW WIRES CLIPS TO THE BACK PANEL & TIGHTEN THEM WITH EXISTING NUTS
SCREW THE OTHER ENDS BACK WITH NUT HOLDING THE BURNER CONNECTOR
LIFTED UP THE SURFACE BURNER PANEL,
OPENED THE BACK RANGE COVER,
UNSCREW THE NUT HOLDING THE BURNER CONNECTOR, DISCONNECT THE REPLACEMENT WIRES ON THE BACK PANEL
TRACE THE NEW WIRES CLIPS TO THE BACK PANEL & TIGHTEN THEM WITH EXISTING NUTS
SCREW THE OTHER ENDS BACK WITH NUT HOLDING THE BURNER CONNECTOR
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Evelyn from FRANKLIN, NH
- Parts Used:
- WB17T10006
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
Two blocks kept shorting out.
After watching the video and ordering the parts and searching for the right size socket (which took most of the time) and finding medical tape as I had no electrical tape I took of the back unhooked the terminals and following the wires to determine which ones needed to be replaced I followed the video instructions on reverse as my son had spliced new terminal blocks into the old wires I taped each new wire to the one it was replacing and pulled it through the back of the stove and into the front attached the new wires to the new block and pushed the clips on the other end of the wires to the knob boxes. I rolled up the excess wire and taped it securely with medical tape so it wouldn't unravel and be in the way when I reattached the back shield on the stove. After I repeated the process for the second terminal (I had two that kept shorting out) I reassembled the stove plugged it back into the wall and used both burners that night to cook dinner! I have had no problems with those burners since then. Really if you watch the video first and follow the instructions you should have no problems. It is really quite simple if someone hasn't tried to repair the problems without replacing the wires. Splicing new blocks into old wires just doesn't work. If I have this problem again, which I hope I don't, I will be confident in my ability to fix the problem myself. Thank you parts select for repair video and the parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from MILROY, PA
- Parts Used:
- WB17T10006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
on off switch smoked and smelled hot
standard procedure, very simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NEIL from ROCKY POINT, NY
- Parts Used:
- WB08T10026
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
BASE OF BULB BROKE OFF & WELDED TO SOCKET
PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.
Was this instruction helpful to you?
Thank you for voting!