JSP34WW4WW General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Charles from MECHANIC FLS, ME
- Parts Used:
- WB17T10006
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Replaced the outlet the one of the top burners on top of my stove, it went very well.
I followed the instructions on the video, the only thing they left out is where the wires go through to the back of the stove being that there are sharp edges. A role of glass tape would have been handy to replace the old tape. Thanks for asking, I hope this helps someone else.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from CLAY, NY
- Parts Used:
- WB44K5012
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
The phillament ends were pointed straight and the one I removed from the oven were bent in an angle .
Bent the tips so the phillament can fit inside the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from Houston, TX
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
oven coil caught on fire and broke in half!
I turned off the main power! Then unscrewed the back cover unhooked the wires and unscrewed the coil inside of the oven and pulled it out. My 10yr old son and I measured it and went online to order the part. I first did go into BestBuy and they didn't have the part (But they tried to sale me a new oven!) LOL Now who said a newly divorced mom couldn't fix her own oven! My Tech Support skills came in handy! Women Rock! LOL
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard L. from Clear Spring, MD
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
No heat lower bake unit / Broiler unit heats ok
Safety first: Turn range circuit breaker to off position. Turn a surface unit [burner] to the on position ,if no light exists power has been removed. Turn surface unit to off position. To remove bake unit. With a 1/4 socket driver remove two self tapping screws and gently pull out on the bake unit until you can access the slide on terninals. Careful lenth of wire is limited. Remove slide on terminals two each [2] . Install new bake unit in reverse order . Restore power
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Mariposa, CA
- Parts Used:
- WB27T10174
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Complete failure of oven controls, no error codes
Was very difficult to be certain of the right controller due to the exact model number of the range did not exist. Somewhat of an expensive part to make a guess.
After contacting no less than 5 parts dealers, Part Select was the only company that could immediately identify the correct number, (the model # on the range had an extra zero in the middle).
Was able to purchase the part confident it was correct, at a good price, with fast shipping.
Thanks
After contacting no less than 5 parts dealers, Part Select was the only company that could immediately identify the correct number, (the model # on the range had an extra zero in the middle).
Was able to purchase the part confident it was correct, at a good price, with fast shipping.
Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jan from Rockport, ME
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven would not get to temperature...200 degrees max
Pull out oven and unplug from 220 outlet. Remove rear upper/lower cover (4 screws), Remove two wires from rear of element. From front, open oven door, remove two screws and pull out old element.
Install new element by reversing above sequence. Then test and push oven back in place. Easy!
Install new element by reversing above sequence. Then test and push oven back in place. Easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lynette from Bowling Green, KY
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Element burned out.
Flipped off the circuit breaker first. Unscrewed the two screws holding the element in place. Pulled out about 4-5 inches. Tried several times to pull apart the connections, finally got 'em - don't give up (I must have weak fingers). Then plugged in the new element, shoved the wires back in, screwed it back in place, flipped circuit breaker back on, turned the oven on.... made brownies (o:
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Coleen from Danville, IN
- Parts Used:
- WB44K5012
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The old heating erlement basically melted and broke in two places
I unscrewed the two screws inside the oven, then i pulled the oven away from the wall and unscrewed the protective shield, and undid the wiring. Then i removed the element. Once the new one arrived, i pretty much just did the same thing in reverse. vwa-lah... fixed!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from OAKLAND, MD
- Parts Used:
- WB23K5027
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Surface burner switch malfunction allowing the burner to remain on high heat after turning to low heat.
I removed two small screws located on the underside of the control panel. I then rotated the bottom of the control panel up and dislodged the few connections at top back of control panel. The control panel became loose enough to lay forward exposing the inner control switches. The old problem switch wiring was removed one by one and placed in the same spot on the new switch. The old switch was then removed by pulling off the front control knob and then unscrewing two screws holding the old switch in place. Then the new switch was installed exactly as the old switch was removed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Rowlett, TX
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner worked intermittently
Lined up the prongs and slid it right in, took 30 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Iron River, MI
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
burnt element
.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from Covington, LA
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Old element burned in half
I turned off the power going to the stove, unscrewed the 2 screws, plugged in the 2 inserts, put the 2 screws back and PRESTO!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth from Charlotte, NC
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
My heatng element blew up
I followed the way all the others on this website did the repair. It was so easy. I turned the power off to the oven, then disconnected it from the back oven wall, pulled it out a bit, disconnected the wires, and put it back in.
Then we put the power back on and stood back and turned on the stove and IT WORKED!!! Yeah, and for so little money... I tell you I shopped other websites and this one was priced GREAT, and just reading the stories how others had done this repair gave me the confidence to do it too. Now, I think I have a burner that I will replace and who knows what else I can find to do.
THANKS SO MUCH!!!
Then we put the power back on and stood back and turned on the stove and IT WORKED!!! Yeah, and for so little money... I tell you I shopped other websites and this one was priced GREAT, and just reading the stories how others had done this repair gave me the confidence to do it too. Now, I think I have a burner that I will replace and who knows what else I can find to do.
THANKS SO MUCH!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Muncie, IN
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Tenant broke bake element
Removed the two screws, pulled out old element, installed new element, and reinstalled screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michele from Dayton, NJ
- Parts Used:
- WB44K5012
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element was not working in an old (50+ years old)GE electric oven
Replacement of the heating element only takes a few minutes...First, turn off the breaker/fuse to the stove, then just remove two screws , pull out the two connected wires to expose the connections, hook them up, and replace the screws to the cover plate. The connection/cover plate can be hinged or not hinged. Make sure you order the correct one. We ordered the wrong one at first, but were assisted by the returns dept. and received the correct one in 2 days. Great customer service, thanks partsselect.com!!
Was this instruction helpful to you?
Thank you for voting!