JCBP79WK3WW General Electric Range - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- bryan from cocoa, FL
- Parts Used:
- WB24T10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
burner was inoperative
verified switch operation , checked continuity of burner element found open ordered new part and installed next day
after extremely fast
service from partselect thank you
after extremely fast
service from partselect thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Greensboro, GA
- Parts Used:
- WB24T10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Burner not heating.
Isolated to control switch.
Replaced
Replaced
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Medina, OH
- Parts Used:
- WB30T10099
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
large burner on the dual element not working
The part arrived much sooner than I anticipated. The job was a little harder and took a little longer for me because I'm not good at repairing things. I usually have to call someone. However, I followed the step by step instructions that were provided both on the website and with the mailed item and had no problems. The instructions were clear and easy to follow. The tools needed were very basic - all of which I had on hand. If I could do it - anyone can.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- brendan from lebanon, NH
- Parts Used:
- WB17T10011
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
one leg of the terminal block was loose and overheated under load.the terminal block melted and could have caused a fire.
I took a picture of the setup and damage . I then disconnected the burnt wires and replaced the wires . Then I installed the new terminal block and connected the wires to the proper positions. The reason for the failure was that the delivery people didn't tighten the cord when they installed the stove . I would check the connections periodically as to avoid another situation like this .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BILLY from WEBSTER, FL
- Parts Used:
- WB24T10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Burner Would Not Turn Off
Replace control switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Owings Mills, MD
- Parts Used:
- WB36X192, WB08T10026
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Wall oven: light flickered or did not work in a loose poreclain socket.
Shut off power at the panel to the electric oven. Removed 2 phillips screws holding bulb unit in place in the top of teh oven chamber. One wire was so frayed it came out of the push on connector. Stripped off insulation and reinstalled onto the connector, using pliers to snug the wires down. Installed the new porcelain socket from Parts Select, replaced the unit in the top of the oven unit. Installed a new bulb, then snapped the new glass housing into place with the existing retaining wire clip. Presto: works like it's brand new. Thanks to Parts Select for the right parts, and for such quick delivery. I will use them again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Kingsville, MD
- Parts Used:
- WB30T10099
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Twisting of stuck cook-top killed the event
The age of the system resulted in the cook top being heavily stuck by food-stuff to the range surface. The result was a twisting of the top when breaking it free. It caused the cooktop (a $500+ part) to crack diagonally across the whole surface. Thus ended the quick do-it-yourself process, and out to buy a new range. Parts-select was very good about the return process of the un-used and un-opened burner element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TERRY from RICHMOND, VA
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
rear drawer supports broke
Directtions were by diagram only, no written instructions. Drawing was small and difficult to follow but the repair itself was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Annapolis, MD
- Parts Used:
- WB21X22134
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
The oven temperature could not be controlled
Disconnect the range from the mains. Open the door. Remove the single screw holding the temperature sensor - this is located on the back wall on center and is screwed to the broiler mounting plate. Remove the four screws holding the boiler element and allow it to hang down on the wire; this exposes a space to feed the wire through later. Now move to the back of the range and remove the six screws that hold the central cover plate. Now push the insulation to up out of the way and you can disconnect the temperature sensor, pull it out through front, insert the new one and connect it. Reassemble in the reverse order. Mine worked perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Harkers Is., NC
- Parts Used:
- WB21X22134
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Oven slow to heat up
Removed oven door. Removed 2 screws from heat sensor on rear upper wall of oven. Pulled unit out to access rear of unit. Removed six screws on shield on back of unit. Dis connected heat sensor wire and pulled old sensor through from inside of oven. Feed wire of new sensor through from inside and plug in. Everything in reverse. I also had the gas(propane) company come out and check the pressure coming out of the "low pres." regulator. It was low, they changed the regulator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Keezletown, VA
- Parts Used:
- WB24T10029
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Replacment of burner control switches
I watched your video on the subject and followed it exactly. It explained everything I needed to know. The hardest part was CLEANING under the stove once I pulled it out from the wall!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynda from Burdock, SD
- Parts Used:
- WB30T10099
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Small burner not working, outside was fine
Followed directions that I found on the internet and it was easy to remove the old burner and replace it with the one I ordered from you. There was no problems at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mario from Deer Park, WA
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Broken drawer support
Followed the example picture on the part bag. Anyone could do this, incredibly easy. Took about 4 minutes to install both sides.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Newark, DE
- Parts Used:
- WB02X33180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Range lower drawer would not stay on track.
Easy to install replacement parts using the screws provided.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from SLIDELL, LA
- Parts Used:
- WB04T10022
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
gasket leaks heat from oven
pull gasket from door bottom and pull gasket to release retainers in door frame. refit new seal in retainer holes and push gasket into slots at bottom of door. done perfect fit.
Was this instruction helpful to you?
Thank you for voting!