Models > JCB900SK1SS > Instructions

JCB900SK1SS General Electric Range - Instructions

Jump to:

All Instructions for the JCB900SK1SS
106 - 120 of 318
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Sherry from SAINT PAUL, MN
Parts Used:
WB56T10105
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Replaced cracked inner oven door glass
This went pretty smoothly. Watch the video and just follow along step-by-step and it goes well. It would have only taken about 30-45 minutes (even being careful and slow) but I ended up placing the glass twice (be very careful and triple check that all the insulation gets poked under the housing and none is sticking out). The first time I had a small piece sticking out. (Use gloves for this part so your hands don't itch). The second time I needed to redo part of it is I forgot one of the spacers on the door handle and had to get that in there so the handle worked properly. I also took the time to clean the oven while the door was off so that took some time. Total I probably had 1.5-2 hours into this project but at least half of that was me cleaning and being fussy. This is an easy repair. I'm not a confident repair person and this wasn't difficult. It was a little time consuming but well worth the cost vs calling a repair person or buying a new appliance. You do need to have a specialty star head on a screwdriver but my simple tool kit had all the tools I needed. The oven has been working great since the repair.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Steve from HENDERSON, TX
Parts Used:
WB24T10063
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers
Dual burner only had hidden setting.
Removed old switch, put metal jumper from old switch to new one and connected wires to the new one . Reinstalled. Works great.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Roger from ALPENA, MI
Parts Used:
WB02T10037
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set
The light socket cup could no longer hold the bracket that holds the light cover in place.
I watched a video of a similar model to familiarize myself with the required steps needed. I opened the back and disconnected the power cord and ground wires connected to the removable socket I then removed the lightbulb and removable socket from the oven interior side. I then removed the defective light socket cup and replaced it with the part I purchased. After replacing the removable socket and lightbulb, the bracket holding the light cover functioned perfectly with the new light socket cup. Final steps were to reconnect the power and ground wires to the removable socket. I then replaced the back cover over the light socket cup area. One word of advise. Be very careful when removing and reconnecting the cables to the removable light socket.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Keith from GOLDSBORO, NC
Parts Used:
WB44T10011
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
bake element burnt out
unscrew and disconnect the old unit. Connect and screw in the new unit
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
kathleen from Wynantskill, NY
Parts Used:
WB24T10119
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
cooktop switch broken
Really easy. Part came in rapid time and was the right part. Went on web and got instructions with video how to install.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Shiirley from CASPER, WY
Parts Used:
WB44T10011
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
Back element was broken
My son did it by using pliers. He took out the screws that held the element in and pulled it out and used the pliers to pull the wires out of the old one and snapped the new one in . put it back together. about 5 minutes.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from BAY CITY, MI
Parts Used:
WB30T10099
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers, Screw drivers
inner element not working
opened oven door and removed two 1/4 " screws from range top. lifted range top and propped open like a car hood with a 1" diam dowel rod. marked on new element the wire color locations from old element and removed wires. removed the two small screws and clips that hold the element to the range top and removed element. Matched where the mounting screws locate to the new element. Installed new element in reverse order.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Paul from Louisville, KY
Parts Used:
WB44T10011
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set
The heating element broke in half.
This was a very simple procedure. I removed the 2 screws in the oven itself (holding the element in place), then pushed the element through the back of the oven so the wires were exposed, then slipped off the wires, the male end from the female end, I then removed the entire element. I put the new element in the over, re-attached the wires, put the screws back in place, replaced the cover, and the oven was as good as new.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sherry from SAINT PAUL, MN
Parts Used:
WB02X38986
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Replacing handle spacer
This one is simple. unscrew a portion of the door, install the spacer and screw back together. Worked well.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Sachin from Omaha, NE
Parts Used:
WB44T10011
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set, Wrench (Adjustable)
Bake unit started on fire then cracked in half.
We ordered the part from PartSelect and received it the next day. Didn't even have to move the range out from the wall. Just unscrewed the two screws on the back wall of the stove that hold the bake element in place with a socket wrench, then pulled the old bake element and wires out about 2-3 inches so we could disconnect the old bake unit. The element was kind of hard to pull out, but after you pull it from the wires, just plug in the new bake unit, push the wires back in and put the screws back in. Oven was up and working again!
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Belinda from Rockford, IL
Parts Used:
WB44T10011
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Lower bake element burned out
I didn't know anything about this repair, other than I was replacing a part, so it never occurred to me that I needed to make sure there was no power to the oven. When I pulled the element out, there was a large spark. I flipped the breaker off, then finished the R&R.

Make sure you turn power off at the breaker, then replace the element.

Tim
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Edmond from BRISTOL, CT
Parts Used:
WB44T10011
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Slow heat recovery
Had to remove rear cover to connect wires, removing them from the front caused the wires to fall into rear.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Canterbury, CT
Parts Used:
WB44T10011
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Oven heater coil burned out
Removed power plug- disconnected wire, removed cover over wires two screws, and removed old heated strip, held in by two screws inside of oven
Slide in new coil installed two screws, connected two wires replaced guard over wires, plugged in stove, cooked a rubarb pie, success
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JEAN-C. from PARRISH, FL
Parts Used:
WB44T10011
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
oven wouldn't heat
removed two screws that hold the element in place and then removed the access rear panel it was much easier to disconnect the element than have to stick my head in the oven to gain access.time :15 minutes.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from Comstock Park, MI
Parts Used:
WB44T10011
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
Bake unit caught fire and a 3 inch section burned away
Becuase of the fire we had used a chemical based fire extinguisher, which made a real mess in the whole main floor of the house. I removed the oven from the house and used a leaf blower to get rid of all the white chemical powder (like a baking soda of sorts). Once that issue was done, I removed the part in less than 5 minutes. Two screws to remove it and then unpluged the two wire clips from the back of the stove under the shield which also had 6 screws to remove. It took only 3 days to have a new one delivered and I installed it in less than 5 minutes. The oven works fine now. It took much longer to clean the house than fix the oven.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JCB900SK1SS
106 - 120 of 318