24588L0 General Electric Range - Instructions

This repair was idiot-proof. Removed 2 screws, unplugged the old part, plugged in the new one, and replaced the 2 screws.
Literally a 2 minute repair!!

Piece of cake. 2 screws and a flashlight. I needed needle nose pliers to insert the "plugs" into the "sockets."

I had grease on the baking element when I turned the oven on. I thought it would burn off, it caught fire and destroyed the baking element. I ordered a new element, it came within two days. I didn't wait for my husband to come home. I got a screw driver, took off the screw, used pliers to pull apart the old baking element from the wires. I did this carefully , our oven is old and the element was not pulling away easily. I inserted the new element, put the screws in and it worked perfectly! I was very proud of myself but the truth is that this is a simple job.

I took out the two racks from inside the oven. I then took my cordless screw driver and unscrewed the two hex bolts from the back of the oven , where the element goes through the other side. Next I went to the back of the outside of the oven and unscrewed the two hex bolts that hold the gray guard on(It covers the wires). I unplugged the red and the yellow (might have been a white wire since it was dark back there). wires that connect to the element. I went to the front of the stove and took out the bad element. I took the new one and inserted it into the two holes from the old element. Plugged the red and yellow wires back up and replaced the guard. Lastly I screwed the element to the rear of the oven with the two hex bolts I used before.

first removed the two screws,pulled the element out ,disconnected the wires, pulled it out , cleaned the oven and then reversed the process. could not have been easier for a do it yourself homeowner on a budget.

The replacement element came within a couple of days of our order. From the time I saw it by the front door till the repair was complete was about 10 minutes. Half the time was taken in walking to my tool box. In just a few minutes we had tested the new element and were ready to make dinner. Great value for the price.

First I unplugged the stove. I then removed the two screws that held the element in place. I then pulled the element out about four inches to expose the connection. I disconnected the two wires, removed the element and replaced it with the new one. I then reassembled the oven in reverse order. It was very simple.

removed two bolts on the inside of the oven, disconnected the two electrical connections in back which were a little set so I had to use pliers and removed old element. Reversed procedure to install new element.

The >15 minutes includes vacuuming out the oven.

partselect.com deliver was extremely fast and the part was packed securely. We would order from them again without a problem.

Removed oven door & shelves. Removed the 2 mounting screws & compared parts to verify I ordered the right one, then plugged it right in! Managed to drop & lose one of the screws while re-installing them. Got a stainless sheet metal screw from the hardware store that fits, but will probably order an exact replacement because the size & thread are slightly different. All in all, other than losing the screw, it was a quick, easy task.

Turned off circuit breaker, removed the two screws, pulled out the wires, unhooked the connections and hooked up the new element. Put the two screws back in, turned on the power and it worked! So, so easy! I wouldn't have attempted it had it not been for the other stories associated with the part I purchased.

replace coil 2 clips off 2 clips on........

I removed the 2 screwws inside the oven cavity and pulled the element towards me. I unplugged the wires from the element and plugged in the new one and secured it in place with the 2 screws.

Shut off electrical supply to stove.Remove 2 screws.
Slide element out enough to remove connectors from element.
Position new element.Slide connectors onto new element.
Slide element back into position.Replace 2 screws.Turn on electrical supply.

Turned off the breaker to the stove, removed oven racks, used small pair of plyers to remove bolts (2) holding defective element in place. Pulled (2) wires that had a snap connection apart. Old element was not removed. Connected (2) snap wires, pushed them back into the oven wall, used plyers to re-connect the element to oven. Installation DONE!
Turned on breaker and then the oven; we are now baking again.

It was real easy all I had to do was turn the breaker off,Undo two srews and disconnect the two wires. Then repeated the process to install