JMS08BW2WH General Electric Range - Instructions

I pulled out the old burner - put the new one in and I was done. No tools required.

The first burner I received from PartSelect was warped. I called on Friday morning to see about returning it and ordering a new one. The CSR was very helpful and I was totally surprised to have the replacement arrive the very next day since I didn't ask for a Saturday delivery. I will definitely use PartSelect again.

Everything was very easy: identifying the right part was very easy on the website, the part came quicker than I expected, and my wife replaced the stove element before I even got home from work. She just pulled the old one out like she would to clean the top of the stove, and put the new one back in. Have had several awesome cups of coffee since the replacement.

Did it By Hand
Your Shipment Time Excellant
Order it Mon. Received it Wed.


Thank You

- removed the old element
- looked for part number, was none
- could not find direct replacement listed
- compared to dimensions on drawing
- ordered part
- discovered that the mounting plate on new element was too small, holes did not line up, did not cover opening in back of oven.
- sawed off mounting plate on new element
- removed mounting plate from old element
-drilled out holes on old mounting plate to accept new element
- attached the modified element
- Everything works fine.

I should note that my first order to PartsSelect.com
was made on-line and that I selected the wrong part by comparing the burned-out element to the web site picture. When I received that part, I phoned and quickly corrected my mistake, ordered the correct part and obtained return instructions.

With the correct part in hand, I removed the two screws holding the element in place, pulled the element out a short distance to disconnect the two wires and removed the burned-out element. Reversing this procedure I installed the new bake element and completed the job by checking out the oven heating. The hardest part of all this was reaching over the oven door and stretching to unscrew and screw the necessary screws.

I spent half an hour finding my driver set. It took about 25 minutes to turn the power off, remove the racks and element and replace the new elements.

Very easy fix. After removing the six screws that held the door together, it was a cinch to replace the end caps and put the door back together. Works just like new!!

It was easy except that I had to make just a small modification to the electrical connection (holes were to small). . . . Other than that, its was a breeze to install.

.Received the part promptly. Installed it in about 30 minutes. With appliance servicemen, I figure I saved about $200.00 doing it myself. Thanks

disconnected electricity, used pinch pliers to remove broken ends from connection box and used an already existing element to make sure a new one would work at all. Ordered new one that arrived very quickly and replaced the broken one. After years of taking these in and out for cleaning by outside cleaning help they are bound to break off. I will do the gentle removal from now on.

I shut off the power at the circuit breaker. I loosened the screws securing the baking element to the back wall. I then pulled out the baking element toward me and found the wire leads bolted using self-tapping screws to the original element. Since the holes on the mounting tabs did not take the old screws, I had to drill out the holes on the tabs of the replacement element. After securely bolting the leads to either terminal on the element, I had to drill two holes on the back wall for the mounting plate of the new element. Then I used the cordless drill with the Philips bit to drive in stainless steel self-tapping screws (not zip screws) to secure the element to the back wall. I turned on the power at the circuit breaker and reset the clock (mechanical).

Needed to drill two new holes for fastening the element to the oven wall. Change in design. Enlarged the holes in the spade connections since I was unable to find smaller bolts than 4-40.
I would suggest to make the holes in the spade connections larger.
The change out was not a problem.

Removed door from unit, removed two screws on the insideof the door and open door in two, (inside and outside), removed two screws from each door handle end, replaced with new ones and Bingo !!!

My son took care of removing the broken parts, opening the door and replacing the new handle ends and then finished! It was easy watching him do the work!!!

removed two screws disconnected old element from the two wires and replaced it with the new element. It saved $60.00 service call.