JGBS10DEM4BB General Electric Range - Instructions

The job was made very simple primarily due to the repair video that was available on your site when I ordered the part that I was looking for. The job can be done in less than 15 min, but it took me a little bit longer because of some rusted screws that didn’t want to come out so easily. I also decided to take of the front door (not mentioned in the video) just to make it a bit easier to reach the igniter component. The door comes off very easy by opening the door about 6 inches and pulling up and off of the door hinges. Again for a novice like me the video was a life saver.

removed the screws holding unit in pkce ,unplugged unit'Then I had to cut plug in off new unit and put old plug on new unit. the new unit only had 1 plug and the stove had a2 plug systtem. The put unit back in by replacing thw screws.

removed bottom drawer, disconnected screws holding burner in place. unplug igniter. remove bottom tray from inside oven, remove 1 screw holding burner in place near door, remove whole burner assembly. take 2 screws holding element in place. screw new element to burner and reverse procedure. only tool i used was a 1/4 in nut driver.

the tips you listed from; edward of Pipersville,Pa and Durwood of Suffield,Ct also Billie J of Western Grove, Ar were very helpful. Thanks to them & to you for posting them they were a time saver

First, I was amazed at how fast I received my order. I ordered the part on a Friday morning and i received it Saturday morning. Standard shipping.
The repair should have been much easier than it was.
I removed the oven door by just pulling up and out. then i removed the door underneath the oven. The i reached underneath and disconnected the igniter. From inside the oven, i removed the bottom panel(2 screws). Then i removed the front screw holding the gas tube. I was able to move the tube enough to get at the two screws holding the igniter. one of the screws came out easily using an adjustable wrench. but the other did not come out straight. i had to use tin snips to cut off the igniter so i could acess the screw easier. replacement was in reverse.

Researched problem came to conclusion that igniter was not staying hot (seemed to intermittently go on and off ). One connector and two screws problem solved and the cherry pies are back in my oven and ready for dessert! : )

replaced the igniter by first removing the pan inside the oven, two screws in the rear. Igniter is attached to the burner with two machine screws, nut driver or small wrench is needed. Remove the lower drawer and un-clip plasitc connection located in the rear up high. Pull the wire and clip through into oven. Replace with new inginater, pull wires and clip through the back of oven and tighten screws, plug clip in, replace pan and plug in oven, done.

Well first off ordered the part on Monday was here by Tuesday before I went to work. Was able to replace the part the next day and had pizza for lunch for me and the little woman.
Just also want to say Thank You.

Uninstalled the igniter and reinstalled the new one.

Repair was very simple. It was a five minute job including time taken to remove old part with a screwdriver and then it was a matter of plugging in the new part ant attaching it to the oven.

It was so easy ! take out 2 screws , unplug old igniter, plug in new igniter, replace screws and turn on the heat!! Thanksgiving Dinner is back to my house with the whole Family!!!

Remove botton pan of the oven to get at the igniter, remove bottom drawer to acess wires ,remove 2- screws from the igniter replace then replace oven bottom and drawer.

replaced the glow bar ignitor

This job is done from the inside of the oven. Remove the drawer on the bottom. Open the oven and remove the bottom panel in oven which is fastened by two screws at the back. Lift up panel and pull foward to remove. Unscrew deflector plate and small plate that covers wiring hole. Remove ignitor from the burner. Replace ignitor. I found that you should also relpace burner at the same time. Burner usually causes the ignitor to go out. My burner had a hole in it and flames were shooting out directly on the ignitor which shortened the life of the ignitor. When you buy the burner it comes with an ignitor, you can't buy burner seperately but you can buy the ignitor seperately, so I recommend buying the kit.

Two back screws that held the bottom plate in the oven, once that is off, 2 screws hold the ignitor on andunplugged the harness plug, plug was really easy to unplug. Put the new one on in less than 10 minutes, A very easy job !!!!!!!!