JGBS10DEM4BB General Electric Range - Instructions

Removed oven shelves, removed lower cover, removed heating element, removed lower drawer and unplugged element.

Remove interior bottom of oven, remove igniter screws, unplug igniter. reinstall igniter.

Two set screws in rear; removed easily with a screwdriver. Old oven floor lifted out easily; new oven floor dropped in just as easily; set screws re-installed. Done. Pleasantly surprised at how easy this went.

The repair was pretty straight forward. I simply removed the old igniter, then I snipped the wires. Using the included wire nuts I spliced the old wires with the new. The longest time was spent looking for my wire strippers. I must say that the customer service was very quick and responsive. I received the part but it was broken. One call to customer service and the new part arrived the next day. Great job!!

I simply followed the you tube video and had the new kit installed in 30 minutes.

This was relatively easy repair remove the bottom tray of your oven remove the screws from the two guards remove the old ignitor replace and reinstall in reverse

Easy

Got the general idea off a u-tube video. Very simple and would have been even easier had I used a 1/4 in nutdriver instead of socket. Removed 2 screws (flathead) on the lower cover of oven. Removed 1 nut holding shield. Removed 1 nut holding protective trap door on rear, pulled coupling through hole and disconnected. Removed 2 nuts holding ignitor. That's it. Replace everything in sequence and your done.

1. Open the package.
2. Remove the knob.
3. Place on range.

First I unplugged the stove. I gently removed the two screws that hold the old element in place. I snipped the wires and then twisted the new wires with the stove wires and placed caps on wires. GENTLY replaced new element with screws. DO NOT OVER TIGHTEN. Then I tested the oven after I put it back together and the oven works perfectly.

Remove the sheet metal that covers the burner and the igniter. For me this was two screws located in the rear of the oven. Two 1/4 inch screws held the igniter in place. I then cut the wires on the faulty igniter as close to the porcelin as possible. I cut the clip off of the new igniter and stripped the ends of all 4 wires, splicing then together with the ceramic wire nuts that were included in the kit. I fed the excess wire to the rear of the stove and reattached the new igniter to its mounting bracket. Replaced sheet metal. Plugged the unit into the outlet and away it went. Worked great.

All it took was for my husband to remove the screws that held the part in place and disconnect the two wires. He then replaced the part, connected the wires and screwed the screws in. We turned the oven on and it worked perfectly.

This is our second part that we have ordered. The frist part was just as easy as the second.

removed lower broiler pan so i could see burner igniter. removed the heat shield in front of the gas valve. (1 screw). started oven. no response from igniter. no gas flow at all. if igniter is bad it will not allow gas to flow. ordered new igniter from parts select for my oven model. got it in a couple of days. it wasnt exactly the same as the original, but was compatible. it came with its own connector, but didnt fit. i had to cut it off and splice in the original connector. i had to remove the burner tube to remove the original igniter because the wire was routed around and behind the tube. it just took a couple of screws to remove it and it pulls right off. this is all accessible on the top of the broiler drawer. installed the two screws on the new igniter and plugged in the connector. started oven and igniter started glowing bright immediatly. oven burner lit off within a few seconds. everything working like new now.

oven and stove top burners worked fine, but broiler would not light. diagnosed problem as bad igniter. ordered parts on line and received them next day with regular shipping!

removed oven door and bake racks. removed old igniter and snipped wires.

installed new igniter and used ceramic wire nuts to attach wire leads.

reinstalled door and racks.

works fine. who knew home repairs could be so easy and fun!

I removed the oven door, the base panel of the oven and slid out the broiler tray. Next, I pulled the wires out of the access hole in the back of the oven, then diconnected the modular plug and removed the 2 screws fastening the ignitor. I tested the ignitor with my ohm meter and found out that it did not have the necessary zero ohms resistance. The meter indicated an open circuit, so I ordered the replacement part, which was delivered in less than 24 hours. Then I reassembled everything and tried the oven. Works like new again.