JB655FK6DS General Electric Range - Instructions

Super easy repair! There are videos online if you have one type of oven, I had the other type (with the little silver plate right above the latch part). The trick is to remove the handle from the assembly itself before removing or placing it in the oven. 4 screws total and I recommend needle nose pliers to help remove the wires.

I began by turning off the breaker in the panel.
Slide the oven out into the open area.
Removed 3 screws in order to remove rear top panel.
Took 2 pictures of the wiring location on the PCB
Removed all wiring going to the circuit board total of 8.
Removed 4 screws in order to remove bad PCB.
Remove faceplate from bad PCB (you will need to place this faceplate on the new PCB.

To Install.
Reverse steps above

THE TWO 8' ROUND HEATING ELEMENT
1. LIFT THE LID OF THE STOVE FROM THE SIDE. SOMETIMES YOU MIGHT HAVE TO PRY IT A LOOSE. BE CAREFUL HOW YOU LIFT IT FROM THE BOTH SIDES WITH A FLAT SCREWDRIVER.
2. BECAREFUL HOW YOU PRY THE WIRING FROM THE OLD HEATING ELEMENT. THE WIRING IS FRAGILE. REMEMBER THE STEPS YOU TOOK TO TAKE A LOOSE THE OLD ONE. I HAD MY SON TO HELP ME BECAUSE I FIRST PULL THE CLAMP BACK WITH THE SCREWDRIVER AND HAD HIM TO HOLD IT TO OLD ONE STILL HOOK UP TO THE WIRING. I PLACE THE NEW ONE IN THE CLIP. THEN I TOOK ONE WIRING AT A TIME TO THE NEW ONE.

Remove the old oven latch and replaced it with the new replacement part. It was very easy to remove and replace with just a few nuts removed

This was simple enough to repair for me, a relative novice. Just remember you need a nut driver to take the back panel off, take a photo of the existing board so you remember which wires go where, and you definitely need a hair dryer to heat up the sticker on the old board so you can remove it and put it on the new board.

One wire at at time then used my razor blade to get front off stuck right back on

Easy

I took off the cover of the stove with a socket 1/4 mm, screwdriver and pliers. Now it works perfectly. thanks.../

As many people have encountered, my oven would not heat but the igniter would be bright orange and glow! Over time, the igniter wears and degrades causing oxidation to the surface. This cause the igniter to fail and operate at a lower current level, below 2.8 amps! Normal igniters operator over 3.0 to 3.1 amps. When is happens, a low current igniter does not have enough input to the control valve to tell the valve to open to allow gas to flow over the igniter to light the oven, thus heat the oven! This has got to be the NUMBER one reason for an oven not heating!

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Once I opened up the back of the range, the sensor wires where there and burnt just like your info said. One nut to take off in the oven and the sensor came right out and the new one went right in. The oven works great, cooked the turkey today. The worst part of the repare was the cleaning behind and under the range, it hasn't moved since it was put in 6 years ago. Very pleased with PS.

replaced oven clock control ref maintenance manual, 4 screws and 8 wires. plugged in new control and op checks good.

Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!

Directtions were by diagram only, no written instructions. Drawing was small and difficult to follow but the repair itself was easy.

Purchased the board installed it and saved about 130 dollars.